OPA2725AIDG4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 6V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | OPA2725 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 6V |
| Number of Elements | 2 |
| Operating Supply Current | 4.3mA |
| Nominal Supply Current | 11mA |
| Output Current | 40mA |
| Slew Rate | 30V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 88 dB |
| Current - Input Bias | 30pA |
| Voltage - Supply, Single/Dual (±) | 4V~12V ±2V~6V |
| Output Current per Channel | 40mA |
| Input Offset Voltage (Vos) | 5mV |
| Bandwidth | 20MHz |
| Neg Supply Voltage-Nom (Vsup) | -6V |
| Unity Gain BW-Nom | 20000 kHz |
| Voltage Gain | 120dB |
| Power Supply Rejection Ratio (PSRR) | 90.46dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 1.5mV |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Dual Supply Voltage | 5V |
| Max I/O Voltage | 5mV |
| Input Offset Current-Max (IIO) | 0.00005μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA2725AIDG4 Overview
Op amp is packaged in 8-SOIC (0.154, 3.90mm Width) case. This is a General Purpose type op amp. The op amp is delivered to you in a Tube case. The number of terminations approaches 8. A total of 8 pins are located on this board. I would like to remind you that this buffer op amp should be powered by an 6V battery. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. In total, the buffer amplifier consists of 8 pins. In terms of the input offset voltage, instrumentation amplifier rates at 5mV. Surface Mount is the recommended mounting type of operational amplifiers. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~125°C for optimal performance. It is possible to operate this buffer amplifier from a supply current of 4.3mA . 120dB should remain the voltage gain. This op amp ic outputs Rail-to-Rail signals, which is one of the many benefits it has. As a whole, there are 2 elements that make up this buffer amplifier. The operating supply voltage of instrumentation amplifier is rated 6V voltage.
OPA2725AIDG4 Features
8 Pins
supply voltage of 6V
120dB voltage gain
Output Type: Rail-to-Rail
OPA2725AIDG4 Applications
There are a lot of Texas Instruments OPA2725AIDG4 Instrumentational OP Amps applications.
- Fission chambers
- Portable media players
- High speed sample
- Micro signal measurement
- High input resistance broadband
- Blood pressure sensors
- Mobile phone
- Band-stop filter
- Radar
- Weak signal detection
