OPA2725AIDR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 6V |
| Base Part Number | OPA2725 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 6V |
| Number of Elements | 2 |
| Operating Supply Current | 4.3mA |
| Nominal Supply Current | 11mA |
| Output Current | 40mA |
| Slew Rate | 30V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 88 dB |
| Current - Input Bias | 30pA |
| Voltage - Supply, Single/Dual (±) | 4V~12V ±2V~6V |
| Output Current per Channel | 40mA |
| Input Offset Voltage (Vos) | 5mV |
| Bandwidth | 20MHz |
| Neg Supply Voltage-Nom (Vsup) | -6V |
| Unity Gain BW-Nom | 20000 kHz |
| Voltage Gain | 120dB |
| Power Supply Rejection Ratio (PSRR) | 90.46dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 1.5mV |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Max I/O Voltage | 5mV |
| Input Offset Current-Max (IIO) | 0.00005μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA2725AIDR Overview
It is packaged in an 8-SOIC (0.154, 3.90mm Width)-case that protects the operational amplifiers from damage. Buffer amps of this type are called General Purpose-types. There is a Tape & Reel (TR) case that is delivered with the instrumentation amplifiers. During the past two weeks, there have been close to 8 terminations. A total of 8 pins are located on this board. I would like to remind you that this buffer op amp should be powered by an 6V battery. This particular linear amplifier is a type of Operational Amplifier device, to be precise. In total, the buffer amplifier consists of 8 pins. As far as the input offset voltage is concerned, linear amplifier rates at 5mV. This electronic part is recommended for mounting type Surface Mount. With regard to operating temperature, this op amp functions well at -40°C~125°C. Using an 4.3mA supply current, this operational amplifier ics can be operated. There should be no change in the voltage gain at 120dB. In addition to outputting Rail-to-Rail signals, this op amp ic offers a number of other advantages. There is an operating supply voltage rating of 2 for this operational amplifier, which is rated at the manufacturer. The operating supply voltage of the buffer op amp is rated at 6V. As a result of this, the buffer amplifier is packed in TR.
OPA2725AIDR Features
8 Pins
supply voltage of 6V
120dB voltage gain
Output Type: Rail-to-Rail
OPA2725AIDR Applications
There are a lot of Texas Instruments OPA2725AIDR Instrumentational OP Amps applications.
- Addition operation circuits
- Power generator
- High input resistance broadband
- Medical instruments
- Industrial applications including automation
- Signal filtering
- Portable electronic products powered by batteries
- Automation control systems
- Ultrasound transducers
- Laptop
