OPA2727AIDRBT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-VDFN Exposed Pad |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Series | e-trim™ |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | OPA2727 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 6V |
| Number of Elements | 2 |
| Operating Supply Current | 4.3mA |
| Supply Current-Max | 6.5mA |
| Slew Rate | 30V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 86 dB |
| Current - Input Bias | 85pA |
| Voltage - Supply, Single/Dual (±) | 4V~12V ±2V~6V |
| Output Current per Channel | 40mA |
| Input Offset Voltage (Vos) | 150μV |
| Bandwidth | 20MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 20000 kHz |
| Voltage Gain | 120dB |
| Average Bias Current-Max (IIB) | 0.0005μA |
| Power Supply Rejection Ratio (PSRR) | 90.46dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Voltage - Input Offset | 15μV |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.0005μA |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 20MHz |
| Max I/O Voltage | 150μV |
| Input Offset Current-Max (IIO) | 0.0001μA |
| Height | 1mm |
| Length | 3mm |
| Width | 3mm |
| Thickness | 880μm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA2727AIDRBT Overview
A 8-VDFN Exposed Pad case is used to package the op amp. A General Purpose-type buffer amplifier is shown here. Instrumentation amplifier is delivered in a Tape & Reel (TR) case. There is a growing number of terminations approaching the number of 8. Buffer amplifier has a total of 8 pins. The linear amplifier should be run at 5V at all times, so please keep that in mind when using it. This particular linear amplifier is a type of Operational Amplifier device, to be precise. 8 pins are included on the operational amplifiers. With regards to the offset voltage of the input, buffer amplifier is rated at 150μV. Surface Mount is the recommended mounting type of operational amplifiers. It is important to note that this linear amplifier works well at a temperature of -40°C~125°C when it comes to operating temperatureYou can run this op amp ic on 4.3mA . 120dB should be the voltage gain. One of the many benefits of this op amp ic is that it emits Rail-to-Rail signals. The op amp is rated for an operating supply voltage of 2. The operating supply voltage of the buffer op amp is rated at 6V. This linear amplifier pack is based on the TR axis. The e-trim? represents the op amp's series number.
OPA2727AIDRBT Features
8 Pins
supply voltage of 5V
120dB voltage gain
Output Type: Rail-to-Rail
OPA2727AIDRBT Applications
There are a lot of Texas Instruments OPA2727AIDRBT Instrumentational OP Amps applications.
- Weighing systems
- Band-pass filter
- Video data acquisition
- Vehicle electronics
- Professional videography
- Signal filtering
- Test equipment
- Television
- Addition operation circuits
- Proportional operation circuits
