OPA277P
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Base Part Number | OPA277 |
| Pin Count | 8 |
| Operating Supply Voltage | 18V |
| Number of Channels | 1 |
| Operating Supply Current | 790μA |
| Nominal Supply Current | 825μA |
| Slew Rate | 0.8V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 130 dB |
| Current - Input Bias | 500pA |
| Voltage - Supply, Single/Dual (±) | 4V~36V ±2V~18V |
| Output Current per Channel | 35mA |
| Input Offset Voltage (Vos) | 20μV |
| Bandwidth | 1MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 140dB |
| Average Bias Current-Max (IIB) | 0.002μA |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Voltage - Input Offset | 10μV |
| Low-Bias | NO |
| Micropower | YES |
| Programmable Power | NO |
| Dual Supply Voltage | 9V |
| Nominal Gain Bandwidth Product | 1MHz |
| Max I/O Voltage | 20μV |
| Power | NO |
| Height | 5.08mm |
| Length | 9.81mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA277P Overview
There is a 8-DIP (0.300, 7.62mm) case package that contains the instrumentation amplifiers. A General Purpose-type buffer amplifier is shown here. A Tube case is used for delivering the op amp. We are approaching the 8h termination of the year. There are a total of 8 pins on this op amp. I would like to remind you that this buffer op amp should be powered by an 15V battery. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. In total, the buffer amplifier consists of 8 pins. There is an input offset voltage of 20μV for this buffer op amp. For this electrical component, Through Hole is the recommended mounting type. With regard to operating temperature, op amp ranges -40°C~85°C. You can run this op amp ic on 790μA . Voltage gain should remain at 140dB. There are a total of 1 channels available on the op amps. The operating supply voltage of instrumentation amplifier is rated 18V voltage.
OPA277P Features
8 Pins
supply voltage of 15V
140dB voltage gain
OPA277P Applications
There are a lot of Texas Instruments OPA277P Instrumentational OP Amps applications.
- Inverse/same-phase proportional circuit
- Video data acquisition
- Signal operation
- Cinema or auditorium audio system
- Band-stop filter
- Exponential operation circuits
- Fast A/D and D/A converters
- Navigation
- Active probe
- Television
