OPA317IDCKT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 5-TSSOP, SC-70-5, SOT-353 |
| Number of Pins | 5 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | OPA317 |
| Pin Count | 5 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Number of Channels | 1 |
| Operating Supply Current | 21μA |
| Slew Rate | 0.15V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | Zero-Drift |
| Common Mode Rejection Ratio | 108 dB |
| Current - Input Bias | 275pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~5.5V |
| Output Current per Channel | 5mA |
| Input Offset Voltage (Vos) | 20μV |
| Bandwidth | 300 kHz |
| Unity Gain BW-Nom | 300 kHz |
| Voltage Gain | 110dB |
| Average Bias Current-Max (IIB) | 0.0003μA |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Low-Bias | NO |
| Micropower | YES |
| Programmable Power | NO |
| Power | NO |
| Input Voltage Noise Density | 55nV/sqrt Hz |
| Height | 1.1mm |
| Length | 2mm |
| Width | 1.25mm |
| Thickness | 900μm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA317IDCKT Overview
A 5-TSSOP, SC-70-5, SOT-353 case is used to package the op amp. An op amp ic of the Zero-Drift type. As far as the packaging is concerned, buffer op amp is delivered in a Tape & Reel (TR) case. It is estimated that there will be 5 terminations in the next few months. Linear amplifier has a total of 5 pins. The linear amplifier should be run at 5V at all times, so please keep that in mind when using it. In order to be more specific, this instrumentation amplifier is one of the types of Operational Amplifier devices. 5 pins are located on the operational amplifiers. In terms of the input offset voltage, instrumentation amplifier rates at 20μV. For this electrical component, Surface Mount is the recommended mounting type. Regarding the operating temperature of this device, instrumentation amplifier performs well at a temperature of -40°C~125°C . This op amp can operate from a supply current at 21μA. Keeping the voltage gain at 110dB is the best course of action. On the buffer amps, there are 1 channels that can be used. On the output type, there are Rail-to-Rail different types of op amps. A TR-shaped amplifier is used to pack the buffer amps.
OPA317IDCKT Features
5 Pins
supply voltage of 5V
110dB voltage gain
Output Type: Rail-to-Rail
OPA317IDCKT Applications
There are a lot of Texas Instruments OPA317IDCKT Instrumentational OP Amps applications.
- Power generator
- Weighing systems
- Commercial audio systems
- High gain DC amplifier
- High/low-pass filter circuit
- Instrumentation
- Fast A/D and D/A converters
- PDA
- Exponential operation circuits
- Tablets
