OPA322AIDBVT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 6 hours ago) |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Surface Mount | YES |
| Number of Pins | 5 |
| Operating Temperature | -40°C~125°C |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | OPA322 |
| Pin Count | 5 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 2.75V |
| Number of Channels | 1 |
| Operating Supply Current | 1.6mA |
| Nominal Supply Current | 1.5mA |
| Output Current | 65mA |
| Slew Rate | 10V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 90 dB |
| Current - Input Bias | 0.2pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~5.5V ±0.9V~2.75V |
| Output Current per Channel | 65mA |
| Input Offset Voltage (Vos) | 2mV |
| Bandwidth | 20MHz |
| Unity Gain BW-Nom | 20000 kHz |
| Voltage Gain | 130dB |
| Average Bias Current-Max (IIB) | 0.0008μA |
| Power Supply Rejection Ratio (PSRR) | 100dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Voltage - Input Offset | 500μV |
| Low-Bias | YES |
| Micropower | NO |
| Max Frequency | 10MHz |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 20MHz |
| Max I/O Voltage | 2mV |
| Height | 1.45mm |
| Length | 2.9mm |
| Width | 1.6mm |
| Thickness | 1.2mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA322AIDBVT Overview
The linear amplifier is packaged in a SC-74A, SOT-753 case which makes it easy for the consumer to handle. An op amp of this type is a General Purpose-type. There is a Cut Tape (CT) case that is delivered with the instrumentation amplifiers. We are approaching the 5h termination of the year. The pins on this board total to 5 in total. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. The buffer op amp includes 5 pins. With regards to the offset voltage of the input, buffer amplifier is rated at 2mV. For this electrical component, Surface Mount is the recommended mounting type. With regard to operating temperature, this op amp functions well at -40°C~125°C. You can run this op amp ic on 1.6mA . Voltage gain should remain at 130dB. There are a total of 1 channels available on the op amps. One of the many benefits of this op amp ic is that it emits Rail-to-Rail signals. The operating supply voltage of the buffer op amp is rated at 2.75V. The instrumentation amplifier is packed in the form of TR.
OPA322AIDBVT Features
5 Pins
supply voltage of 5V
130dB voltage gain
Output Type: Rail-to-Rail
OPA322AIDBVT Applications
There are a lot of Texas Instruments OPA322AIDBVT Instrumentational OP Amps applications.
- Cinema or auditorium audio system
- Power generator
- ECG equipment
- High-frequency data acquisition systems
- Video computer boards
- High/low-pass filter circuit
- Automation control systems
- Inverse/same-phase proportional circuit
- Video amplifiers
- Switching amplifier
