OPA330AIDBVT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Surface Mount | YES |
| Number of Pins | 5 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | OPA330 |
| Pin Count | 5 |
| Output Type | Rail-to-Rail |
| Number of Channels | 1 |
| Operating Supply Current | 21μA |
| Nominal Supply Current | 21μA |
| Output Current | 5mA |
| Slew Rate | 0.16V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | Zero-Drift |
| Common Mode Rejection Ratio | 100 dB |
| Current - Input Bias | 200pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~5.5V ±0.9V~2.75V |
| Output Current per Channel | 5mA |
| Input Offset Voltage (Vos) | 50μV |
| Bandwidth | 350 kHz |
| Unity Gain BW-Nom | 350 kHz |
| Voltage Gain | 115dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Voltage - Input Offset | 8μV |
| Low-Bias | YES |
| Micropower | YES |
| Max Frequency | 10Hz |
| Programmable Power | NO |
| Max I/O Voltage | 50μV |
| Power | NO |
| Height | 1.45mm |
| Length | 2.9mm |
| Width | 1.6mm |
| Thickness | 1.2mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA330AIDBVT Overview
The linear amplifier is packaged in a SC-74A, SOT-753 case which makes it easy for the consumer to handle. Op amps are Zero-Drift types of amplifier on the chip. As far as the packaging is concerned, buffer op amp is delivered in a Tape & Reel (TR) case. There have been a total of 5 terminations over the past year. Linear amplifier has a total of 5 pins. Please take in mind that this instrumentation amplifier should be run at 5V. In more specific terms, this linear amplifier can be categoriOperational Amplifiered as a Operational Amplifier-type device. 5 pins are located on the operational amplifiers. Regarding input offset voltage, buffer amplifier rates 50μV voltage. This electronic part is best mounted with type Surface Mount. According to the manufacturer, this buffer op amp works well at -40°C~125°C , which is a good operating temperature. The buffer amplifier is capable of operating from a supply current of 21μA . Voltage gain should remain at 115dB. As far as the device is concerned, buffer amplifier has 1 channels. One of the many advantages that this linear amplifier has, among many other things, is the fact that it outputs Rail-to-Rail signals. An buffer amplifier is packed in a TR-shape according to the design.
OPA330AIDBVT Features
5 Pins
supply voltage of 5V
115dB voltage gain
Output Type: Rail-to-Rail
OPA330AIDBVT Applications
There are a lot of Texas Instruments OPA330AIDBVT Instrumentational OP Amps applications.
- Signal filtering
- Inverse/same-phase proportional circuit
- Strain gauges
- Power transmission
- Radar
- Vehicle electronics
- Non-polarized electrodes
- RF cable systems
- Automation control systems
- Integrator circuits
