OPA330AIDR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | OPA330 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Number of Elements | 1 |
| Operating Supply Current | 21μA |
| Nominal Supply Current | 21μA |
| Output Current | 5mA |
| Slew Rate | 0.16V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | Zero-Drift |
| Common Mode Rejection Ratio | 100 dB |
| Current - Input Bias | 200pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~5.5V ±0.9V~2.75V |
| Output Current per Channel | 5mA |
| Input Offset Voltage (Vos) | 50μV |
| Gain Bandwidth Product | 350kHz |
| Unity Gain BW-Nom | 350 kHz |
| Voltage Gain | 115dB |
| Average Bias Current-Max (IIB) | 0.0005μA |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Voltage - Input Offset | 8μV |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.0005μA |
| Programmable Power | NO |
| Max I/O Voltage | 50μV |
| Wideband | NO |
| Power | NO |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA330AIDR Overview
There is a 8-SOIC (0.154, 3.90mm Width) case in which the instrumentation amplifier is packaged. This is a Zero-Drift type op amp. The op amp is delivered to you in a Tape & Reel (TR) case. During the past two weeks, there have been close to 8 terminations. Buffer amplifier has a total of 8 pins on it. It would be helpful if you could remember that this op amp ic should be powered by an 5V battery. To be specific, this instrumentation amplifier is a type of Operational Amplifier. 8 pins are located on the operational amplifiers. In terms of the input offset voltage, instrumentation amplifier rates at 50μV. It is recommended that this electronic component be mounted using the Surface Mount mounting type. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~125°C for optimal performance. It is possible to operate this buffer amplifier from a supply current of 21μA . 115dB should remain the voltage gain. Buffer amplifier produces Rail-to-Rail signals, which is one of its many benefits. The buffer op amp is rated for an operating voltage of 1 when it comes to the power supply. For packing the buffer amplifier, the TR-axis is adopted.
OPA330AIDR Features
8 Pins
supply voltage of 5V
115dB voltage gain
Output Type: Rail-to-Rail
OPA330AIDR Applications
There are a lot of Texas Instruments OPA330AIDR Instrumentational OP Amps applications.
- Test equipment
- single/dual op amp sum and difference circuits
- Polarized electrodes
- Signal operation
- Exponential operation circuits
- Power generator
- Vehicle electronics
- Digital cameras
- Medical imaging
- Comparator
