OPA333AIDCKT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 5-TSSOP, SC-70-5, SOT-353 |
| Surface Mount | YES |
| Number of Pins | 5 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | OPA333 |
| Pin Count | 5 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 2.75V |
| Number of Channels | 1 |
| Operating Supply Current | 17μA |
| Nominal Supply Current | 25μA |
| Output Current | 5mA |
| Slew Rate | 0.16V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | Zero-Drift |
| Common Mode Rejection Ratio | 106 dB |
| Current - Input Bias | 70pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~5.5V ±0.9V~2.75V |
| Output Current per Channel | 5mA |
| Input Offset Voltage (Vos) | 10μV |
| Bandwidth | 350 kHz |
| Unity Gain BW-Nom | 350 kHz |
| Voltage Gain | 130dB |
| Average Bias Current-Max (IIB) | 0.0002μA |
| Power Supply Rejection Ratio (PSRR) | 120dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Voltage - Input Offset | 2μV |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.0002μA |
| Programmable Power | NO |
| Max I/O Voltage | 10μV |
| Input Offset Current-Max (IIO) | 0.0004μA |
| Height | 1.1mm |
| Length | 2mm |
| Width | 1.25mm |
| Thickness | 900μm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA333AIDCKT Overview
Packaged in a 5-TSSOP, SC-70-5, SOT-353 case, the buffer op amp is ready to use. This is a Zero-Drift type op amp. A Tape & Reel (TR) case is used to deliver the buffer op amp. It is estimated that there will be 5 terminations in the next few months. In this case, there are 5 pins on the board. The linear amplifier should be run at 5V at all times, so please keep that in mind when using it. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. A total of 5 pins are present on the instrumentation amplifier. In terms of input offset voltage, operational amplifier rates 10μV. Surface Mount is the recommended mounting type for this linear amplifier. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about -40°C~125°C . It is possible to operate this buffer amplifier from a supply current of 17μA . There should be no change in the voltage gain at 130dB. There are a total of 1 channels available on the op amps. A benefit of this op amp ic is that it outputs Rail-to-Rail signals, which is one of the many advantages it has to offer. The operating supply voltage of the buffer op amp is rated at 2.75V. It is used TR to pack the op amps.
OPA333AIDCKT Features
5 Pins
supply voltage of 5V
130dB voltage gain
Output Type: Rail-to-Rail
OPA333AIDCKT Applications
There are a lot of Texas Instruments OPA333AIDCKT Instrumentational OP Amps applications.
- Portable media players
- Portable docking station
- Ultrasound transducers
- High input resistance broadband
- Semiconductor detectors
- Subtraction operation circuits
- Test equipment
- Inverse/same-phase proportional circuit
- Exponential operation circuits
- Industrial control system
