OPA347PAG4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 6 days ago) |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 8 |
| Operating Temperature | -55°C~125°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Base Part Number | OPA347 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Number of Elements | 1 |
| Power Supplies | 3/5V |
| Operating Supply Current | 20μA |
| Nominal Supply Current | 34μA |
| Slew Rate | 0.17V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 0.5pA |
| Voltage - Supply, Single/Dual (±) | 2.3V~5.5V ±1.15V~2.75V |
| Output Current per Channel | 17mA |
| Input Offset Voltage (Vos) | 6mV |
| Bandwidth | 350 kHz |
| Unity Gain BW-Nom | 350 kHz |
| Voltage Gain | 115dB |
| Power Supply Rejection Ratio (PSRR) | 84.44dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7.5V |
| Voltage - Input Offset | 2mV |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 350 kHz |
| Max I/O Voltage | 6mV |
| Height | 5.08mm |
| Length | 9.81mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA347PAG4 Overview
There is a 8-DIP (0.300, 7.62mm) case package that contains the instrumentation amplifiers. An op amp ic of the General Purpose type. A Tube case is used for delivering the op amp. In recent months, the number of terminations has approached 8. A total of 8 pins are attached to buffer op amp. Please take in mind that this instrumentation amplifier should be run at 5V. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. There are 8 pins on this chip. In terms of the input offset voltage, instrumentation amplifier rates at 6mV. This electronic component is recommended to be mounted using the mounting type Through Hole. With regard to operating temperature, this op amp functions well at -55°C~125°C. You can run this op amp ic on 20μA . Maintain 115dB as the voltage gain. One of the advantages of this op amp is that it outputs Rail-to-Rail signals, which is one of its many advantages. There is an operating supply voltage rating of 1 for this operational amplifier, which is rated at the manufacturer.
OPA347PAG4 Features
8 Pins
supply voltage of 5V
115dB voltage gain
Output Type: Rail-to-Rail
OPA347PAG4 Applications
There are a lot of Texas Instruments OPA347PAG4 Instrumentational OP Amps applications.
- Micro signal measurement
- Multiplication circuits
- Automatic control
- Vehicle electronics
- Precision measurement
- pH (acidity)
- Tablets
- Logarithmic operation circuits
- Medical instruments
- Signal operation
