OPA348AIDCKTG4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 6 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 5-TSSOP, SC-70-5, SOT-353 |
| Surface Mount | YES |
| Number of Pins | 5 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | OPA348 |
| Pin Count | 5 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Number of Elements | 1 |
| Operating Supply Current | 45μA |
| Nominal Supply Current | 65μA |
| Slew Rate | 0.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 0.5pA |
| Voltage - Supply, Single/Dual (±) | 2.1V~5.5V |
| Output Current per Channel | 10mA |
| Input Offset Voltage (Vos) | 5mV |
| Bandwidth | 1MHz |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 108dB |
| Power Supply Rejection Ratio (PSRR) | 84.44dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 1mV |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 1MHz |
| Max I/O Voltage | 5mV |
| Height | 1.1mm |
| Length | 2mm |
| Width | 1.25mm |
| Thickness | 900μm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA348AIDCKTG4 Overview
The linear amplifier is packaged in a 5-TSSOP, SC-70-5, SOT-353 case. The instrumentation amplifier in this picture is of the General Purpose-type. A Tape & Reel (TR) case is used to deliver the buffer op amp. There is a growing number of terminations approaching the number of 5. A total of 5 pins are located on this board. It is important to remember that this op amp should be operated at a voltage of 5V volts. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. 5 pins are located on the operational amplifiers. Regarding input offset voltage, buffer amplifier rates 5mV voltage. For this electronic part, it is recommended that you mount it with type Surface Mount. The buffer amplifier functions well at -40°C~125°C as far as operating temperature is concerned. This op amp can operate from a supply current at 45μA. There should be no change in the voltage gain. As one of the many benefits of this buffer amplifier, it puts out Rail-to-Rail signals, which is one of the many benefits it offers. A total of 1 elements are present in this linear amplifier. An buffer amplifier is packed in a TR-shape according to the design.
OPA348AIDCKTG4 Features
5 Pins
supply voltage of 5V
108dB voltage gain
Output Type: Rail-to-Rail
OPA348AIDCKTG4 Applications
There are a lot of Texas Instruments OPA348AIDCKTG4 Instrumentational OP Amps applications.
- Video conversion and routing
- Medical instruments
- Weighing systems
- Portable electronic products powered by batteries
- Oscilloscopes
- Weak signal detection
- Active probe
- Power transmission
- High/low-pass filter circuit
- Comparator
