OPA354AIDDA
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-PowerSOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | OPA354 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Number of Channels | 1 |
| Operating Supply Current | 4.9mA |
| Nominal Supply Current | 6mA |
| Slew Rate | 150V/μs |
| Amplifier Type | Voltage Feedback |
| Common Mode Rejection Ratio | 56 dB |
| Current - Input Bias | 3pA |
| Voltage - Supply, Single/Dual (±) | 2.5V~5.5V ±1.25V~2.75V |
| Output Current per Channel | 100mA |
| Input Offset Voltage (Vos) | 8mV |
| Bandwidth | 100MHz |
| Unity Gain BW-Nom | 100000 kHz |
| Voltage Gain | 110dB |
| Average Bias Current-Max (IIB) | 0.00005μA |
| Power Supply Rejection Ratio (PSRR) | 73.98dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7.5V |
| Voltage - Input Offset | 2mV |
| Settling Time | 30 ns |
| Low-Bias | YES |
| Micropower | NO |
| -3db Bandwidth | 250MHz |
| Bias Current-Max (IIB) @25C | 0.00005μA |
| Programmable Power | NO |
| Input Offset Current-Max (IIO) | 0.00005μA |
| Height | 1.7mm |
| Length | 4.89mm |
| Width | 3.9mm |
| Thickness | 1.48mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA354AIDDA Overview
Op amp is packaged in 8-PowerSOIC (0.154, 3.90mm Width) case. Voltage Feedback-type instrumentation amplifiers are used in this application. Upon delivery, op amp ic is packaged in a Tube case. It is estimated that there will be 8 terminations in the next few months. The pins on this board total to 8 in total. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. A type of Operational Amplifier buffer op amp is what this device is specifically, to be more precise. 8 pins are included on the operational amplifiers. As far as the input offset voltage is concerned, linear amplifier rates at 8mV. This electrical part should be mounted using type Surface Mount. In terms of operating temperatures, this buffer amplifier works very well at a temperature of around -40°C~125°C . Using a supply current of 4.9mA , this buffer op amp will be able to operate. Op amp is a member of the 110dB's 110dB family. On the buffer amps, there are 1 channels that can be used. One of the many advantages that this linear amplifier has, among many other things, is the fact that it outputs Rail-to-Rail signals.
OPA354AIDDA Features
8 Pins
supply voltage of 5V
110dB voltage gain
Output Type: Rail-to-Rail
OPA354AIDDA Applications
There are a lot of Texas Instruments OPA354AIDDA Instrumentational OP Amps applications.
- Proportional operation circuits
- Medical instruments
- Integrator circuits
- Exponential operation circuits
- Television
- High/low-pass filter circuit
- Logarithmic operation circuits
- Portable electronic products powered by batteries
- earphone
- Ultrasound transducers
