OPA355NA/250
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Contact Plating | Gold |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-6 |
| Surface Mount | YES |
| Number of Pins | 6 |
| Operating Temperature | -40°C~125°C |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.95mm |
| Base Part Number | OPA355 |
| Pin Count | 6 |
| Output Type | Rail-to-Rail |
| Number of Channels | 1 |
| Operating Supply Current | 8.3mA |
| Nominal Supply Current | 11mA |
| Slew Rate | 360V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | CMOS |
| Common Mode Rejection Ratio | 66 dB |
| Current - Input Bias | 3pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~5.5V |
| Output Current per Channel | 100mA |
| Input Offset Voltage (Vos) | 9mV |
| Bandwidth | 200MHz |
| Unity Gain BW-Nom | 200000 kHz |
| Voltage Gain | 92dB |
| Average Bias Current-Max (IIB) | 0.00005μA |
| Power Supply Rejection Ratio (PSRR) | 81.94dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7.5V |
| Settling Time | 30 ns |
| Low-Bias | YES |
| Micropower | NO |
| -3db Bandwidth | 450MHz |
| Bias Current-Max (IIB) @25C | 0.00005μA |
| Programmable Power | NO |
| Max I/O Voltage | 2mV |
| Input Offset Current-Max (IIO) | 0.00005μA |
| Height | 1.45mm |
| Length | 2.9mm |
| Width | 1.6mm |
| Thickness | 1.2mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA355NA/250 Overview
A SOT-23-6 case is used to package the op amp. Buffer amps of this type are called CMOS-types. The op amp is delivered to you in a Cut Tape (CT) case. During the past two weeks, there have been close to 6 terminations. Buffer amplifier has a total of 6 pins. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. A type of Operational Amplifier buffer op amp is what this device is specifically, to be more precise. 6 pins are available on the instrumentation amplifier. Op amp ic rates 9mV for input offset voltage. This electronic part is recommended for mounting type Surface Mount. It is important to note that this linear amplifier works well at a temperature of -40°C~125°C when it comes to operating temperatureOperational amplifier can operate supply current at 8.3mA. Op amp is a member of the 92dB's 92dB family. The op amp ic has 1 channels on it. Buffer amplifier produces Rail-to-Rail signals, which is one of its many benefits. To pack the operational amplifier ics, TR is adopted as the packing method.
OPA355NA/250 Features
6 Pins
supply voltage of 5V
92dB voltage gain
Output Type: Rail-to-Rail
OPA355NA/250 Applications
There are a lot of Texas Instruments OPA355NA/250 Instrumentational OP Amps applications.
- Exponential operation circuits
- Addition operation circuits
- Computer workstations
- Radar
- Power generator
- Comparator
- Thermocouples
- Video computer boards
- earphone
- Tablets
