OPA355QDBVRQ1
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-6 |
| Number of Pins | 6 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Series | Automotive, AEC-Q100 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.95mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | OPA355 |
| Pin Count | 6 |
| Output Type | Rail-to-Rail |
| Number of Circuits | 1 |
| Operating Supply Current | 8.3mA |
| Slew Rate | 360V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | CMOS |
| Common Mode Rejection Ratio | 66 dB |
| Current - Input Bias | 3pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~5.5V |
| Output Current per Channel | 100mA |
| Input Offset Voltage (Vos) | 2mV |
| Gain Bandwidth Product | 200MHz |
| Unity Gain BW-Nom | 200000 kHz |
| Voltage Gain | 92dB |
| Average Bias Current-Max (IIB) | 0.00005μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7.5V |
| Low-Bias | YES |
| Micropower | NO |
| -3db Bandwidth | 450MHz |
| Bias Current-Max (IIB) @25C | 0.00005μA |
| Programmable Power | NO |
| Wideband | YES |
| Power | NO |
| Height | 1.45mm |
| Length | 2.9mm |
| Width | 1.6mm |
| Thickness | 1.2mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA355QDBVRQ1 Overview
There is a SOT-23-6 case in which the instrumentation amplifier is packaged. This is a CMOS type op amp. A Tape & Reel (TR) case is used to deliver the buffer op amp. A total of 6 terminations have been reported in the past few weeks. Buffer amplifier has a total of 6 pins. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 3V. To be specific, this instrumentation amplifier is a type of Operational Amplifier. There are 6 pins on this chip. In terms of the input offset voltage, instrumentation amplifier rates at 2mV. For this electronic part, it is recommended that you mount it with type Surface Mount. In terms of operating temperatures, this buffer amplifier works very well at a temperature of around -40°C~125°C . Using an 8.3mA supply current, this operational amplifier ics can be operated. There should be no change in the voltage gain. This op amp ic has 1 circuits. One of the many benefits of this op amp ic is that it emits Rail-to-Rail signals. It is used TR to pack the op amps. In this case, Automotive, AEC-Q100 represents the instrumentation amplifiers' series number.
OPA355QDBVRQ1 Features
6 Pins
supply voltage of 3V
92dB voltage gain
Output Type: Rail-to-Rail
OPA355QDBVRQ1 Applications
There are a lot of Texas Instruments OPA355QDBVRQ1 Instrumentational OP Amps applications.
- Multimedia playback equipment
- Radar
- Switching amplifier
- Thermocouples
- Medical instruments
- Proportional counter tubes
- RF cable systems
- Micro signal measurement
- Video conversion and routing
- High-frequency data acquisition systems
