OPA355UA/2K5
| Parameters | |
|---|---|
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7.5V |
| Settling Time | 30 ns |
| Low-Bias | YES |
| Micropower | NO |
| -3db Bandwidth | 450MHz |
| Bias Current-Max (IIB) @25C | 0.00005μA |
| Programmable Power | NO |
| Max I/O Voltage | 2mV |
| Input Offset Current-Max (IIO) | 0.00005μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Weight | 75.891673mg |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | OPA355 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Number of Elements | 1 |
| Operating Supply Current | 8.3mA |
| Nominal Supply Current | 11mA |
| Slew Rate | 360V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | CMOS |
| Common Mode Rejection Ratio | 66 dB |
| Current - Input Bias | 3pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~5.5V |
| Output Current per Channel | 100mA |
| Input Offset Voltage (Vos) | 9mV |
| Bandwidth | 200MHz |
| Unity Gain BW-Nom | 200000 kHz |
| Voltage Gain | 92dB |
| Average Bias Current-Max (IIB) | 0.00005μA |
| Power Supply Rejection Ratio (PSRR) | 81.94dB |
| Low-Offset | NO |
OPA355UA/2K5 Overview
The linear amplifier is packaged in a 8-SOIC (0.154, 3.90mm Width) case which makes it easy for the consumer to handle. Buffer amps of this type are called CMOS-types. A Tape & Reel (TR) case is used for delivering the op amp. It is estimated that there will be 8 terminations in the next few months. Linear amplifier has a total of 8 pins. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. To be specific, this instrumentation amplifier is a type of Operational Amplifier. The buffer op amp includes 8 pins. Op amp rates 9mV as input offset voltage. Surface Mount is the recommended mounting type for this linear amplifier. It is important to note that this linear amplifier works well at a temperature of -40°C~125°C when it comes to operating temperatureUsing an 8.3mA supply current, this operational amplifier ics can be operated. It is recommended to keep the voltage gain at 92dB at all times. One of the many advantages that this linear amplifier has, among many other things, is the fact that it outputs Rail-to-Rail signals. A total of 1 elements are present in this linear amplifier. An buffer amplifier is packed in a TR-shape according to the design.
OPA355UA/2K5 Features
8 Pins
supply voltage of 5V
92dB voltage gain
Output Type: Rail-to-Rail
OPA355UA/2K5 Applications
There are a lot of Texas Instruments OPA355UA/2K5 Instrumentational OP Amps applications.
- Measurements of Wheatstone bridge
- Switching amplifier
- Power transmission
- Power control
- High-frequency data acquisition systems
- Cinema or auditorium audio system
- Medical instruments
- Non-polarized electrodes
- Weak signal detection
- Communication
