Parameters |
Power Supply Rejection Ratio (PSRR) |
81.94dB |
Low-Offset |
NO |
Frequency Compensation |
YES |
Voltage - Input Offset |
1mV |
Low-Bias |
YES |
Micropower |
NO |
Programmable Power |
NO |
Max I/O Voltage |
2.5mV |
Height |
1.45mm |
Length |
2.9mm |
Width |
1.6mm |
Thickness |
1.2mm |
Radiation Hardening |
No |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 2 days ago) |
Mounting Type |
Surface Mount |
Package / Case |
SC-74A, SOT-753 |
Surface Mount |
YES |
Number of Pins |
5 |
Operating Temperature |
-40°C~125°C |
Packaging |
Tape & Reel (TR) |
JESD-609 Code |
e4 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
2 (1 Year) |
Number of Terminations |
5 |
ECCN Code |
EAR99 |
Terminal Finish |
Nickel/Palladium/Gold (Ni/Pd/Au) |
Subcategory |
Operational Amplifier |
Packing Method |
TR |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
3.6V |
Base Part Number |
OPA364 |
Pin Count |
5 |
Output Type |
Rail-to-Rail |
Operating Supply Voltage |
2.75V |
Number of Channels |
1 |
Operating Supply Current |
1.1mA |
Nominal Supply Current |
1.4mA |
Slew Rate |
5V/μs |
Architecture |
VOLTAGE-FEEDBACK |
Amplifier Type |
General Purpose |
Common Mode Rejection Ratio |
74 dB |
Current - Input Bias |
1pA |
Voltage - Supply, Single/Dual (±) |
1.8V~5.5V ±0.9V~2.75V |
Output Current per Channel |
85mA |
Input Offset Voltage (Vos) |
2.5mV |
Bandwidth |
7MHz |
Unity Gain BW-Nom |
7000 kHz |
Voltage Gain |
100dB |
OPA364AIDBVR Overview
There is a SC-74A, SOT-753 case in which the instrumentation amplifier is packaged. The instrumentation amplifier in this picture is of the General Purpose-type. Upon delivery, op amp ic is packaged in a Tape & Reel (TR) case. A total of 5 terminations have been reported in the past few weeks. It consists of a total of 5 pins in total. I would like to remind you that this buffer op amp should be powered by an 3.6V battery. To be specific, this instrumentation amplifier is a type of Operational Amplifier. It has 5 pins that make up the linear amplifier. With regards to the offset voltage of the input, buffer amplifier is rated at 2.5mV. This electronic component is recommended to be mounted using the mounting type Surface Mount. With regard to operating temperature, this op amp functions well at -40°C~125°C. A supply current of 1.1mA can be used to operate this linear amplifier. It is recommended to keep the voltage gain at 100dB at all times. Instrumentation amplifier has 1 channels on it. One of the advantages of this op amp is that it outputs Rail-to-Rail signals, which is one of its many advantages. The operating supply voltage of instrumentation amplifier is rated 2.75V voltage. To pack the operational amplifier ics, TR is adopted as the packing method.
OPA364AIDBVR Features
5 Pins
supply voltage of 3.6V
100dB voltage gain
Output Type: Rail-to-Rail
OPA364AIDBVR Applications
There are a lot of Texas Instruments OPA364AIDBVR Instrumentational OP Amps applications.
- Weighing systems
- earphone
- Weak signal detection
- Portable electronic products powered by batteries
- RF cable systems
- High-frequency data acquisition systems
- Non-polarized electrodes
- Exponential operation circuits
- Integrator circuits
- Differentiator circuits