OPA364IDBVTG4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Surface Mount | YES |
| Number of Pins | 5 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.6V |
| Base Part Number | OPA364 |
| Pin Count | 5 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 2.75V |
| Number of Channels | 1 |
| Operating Supply Current | 1.1mA |
| Nominal Supply Current | 1.4mA |
| Slew Rate | 5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 74 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~5.5V ±0.9V~2.75V |
| Output Current per Channel | 85mA |
| Input Offset Voltage (Vos) | 500μV |
| Bandwidth | 7MHz |
| Unity Gain BW-Nom | 7000 kHz |
| Voltage Gain | 100dB |
| Power Supply Rejection Ratio (PSRR) | 81.94dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Max I/O Voltage | 500μV |
| Height | 1.45mm |
| Length | 2.9mm |
| Width | 1.6mm |
| Thickness | 1.2mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA364IDBVTG4 Overview
It is packaged in an SC-74A, SOT-753-case that protects the operational amplifiers from damage. Op amps are General Purpose types of amplifier on the chip. In the case of Tape & Reel (TR) cases, linear amplifier will be delivered. It is estimated that there will be 5 terminations in the next few months. The pins on this board total to 5 in total. As a reminder, this buffer op amp should be powered by 3.6V battery and that the battery should be inserted in the amplifier. It should be noted that this type of buffer amplifier is exactly what is known as a Operational Amplifier device. An 5-pin op amp ic is included in the package. There is an input offset voltage of 500μV for this buffer op amp. This electronic part is best mounted with type Surface Mount. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~125°C for optimal performance. It is possible to operate this buffer amplifier from a supply current of 1.1mA . 100dB should remain the voltage gain. There are 1 channels on the operational amplifiers. There are more than a few advantages to using this instrumentation amplifier, one of which is that it outputs Rail-to-Rail signals. The operating supply voltage of instrumentation amplifier is rated 2.75V voltage. The linear amplifier is packaged by using a TR axis.
OPA364IDBVTG4 Features
5 Pins
supply voltage of 3.6V
100dB voltage gain
Output Type: Rail-to-Rail
OPA364IDBVTG4 Applications
There are a lot of Texas Instruments OPA364IDBVTG4 Instrumentational OP Amps applications.
- Signal operation
- Weak signal detection
- single/dual op amp sum and difference circuits
- High speed sample
- Blood pressure sensors
- Inverse/same-phase proportional circuit
- Power generator
- Logarithmic operation circuits
- Switching amplifier
- Car stereo
