OPA373AIDRG4
| Parameters | |
|---|---|
| Nominal Gain Bandwidth Product | 6.5MHz |
| Max I/O Voltage | 5mV |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | OPA373 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Number of Elements | 1 |
| Power Supplies | 3/5V |
| Operating Supply Current | 585μA |
| Nominal Supply Current | 750μA |
| Slew Rate | 5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 0.5pA |
| Voltage - Supply, Single/Dual (±) | 2.3V~5.5V ±1.15V~2.75V |
| Input Offset Voltage (Vos) | 5mV |
| Bandwidth | 6.5MHz |
| Unity Gain BW-Nom | 6500 kHz |
| Voltage Gain | 110dB |
| Power Supply Rejection Ratio (PSRR) | 92.04dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Voltage - Input Offset | 1mV |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
OPA373AIDRG4 Overview
A 8-SOIC (0.154, 3.90mm Width) case is used to package the op amp. There are two types of operational amplifiers in this circuit. Upon delivery, op amp ic is packaged in a Tape & Reel (TR) case. There is a growing number of terminations approaching the number of 8. A total of 8 pins are attached to buffer op amp. It would be helpful if you could remember that this op amp ic should be powered by an 5V battery. In more specific terms, this linear amplifier can be categoriOperational Amplifiered as a Operational Amplifier-type device. 8 pins are included on the operational amplifiers. With regard to input offset voltage, instrumentation amplifier is rated at 5mV. This electrical part should be mounted using type Surface Mount. In terms of operating temperature, this instrumentation amplifier is well suited to a temperature range of -40°C~125°C. Using an 585μA supply current, this operational amplifier ics can be operated. Voltage gain should remain at 110dB. One of its many advantages is that buffer op amp outputs Rail-to-Rail signals. The buffer op amp is rated for an operating voltage of 1 when it comes to the power supply. As a result of this, the buffer amplifier is packed in TR.
OPA373AIDRG4 Features
8 Pins
supply voltage of 5V
110dB voltage gain
Output Type: Rail-to-Rail
OPA373AIDRG4 Applications
There are a lot of Texas Instruments OPA373AIDRG4 Instrumentational OP Amps applications.
- Television
- Digital cameras
- Commercial audio systems
- Gaming industry
- Video data acquisition
- Integrator circuits
- Active probe
- Portable media players
- Measurements of Wheatstone bridge
- Inverse/same-phase proportional circuit
