OPA374AIDBVTG4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Surface Mount | YES |
| Number of Pins | 5 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | OPA374 |
| Pin Count | 5 |
| Output Type | Rail-to-Rail |
| Number of Channels | 1 |
| Operating Supply Current | 585μA |
| Nominal Supply Current | 750μA |
| Slew Rate | 5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 0.5pA |
| Voltage - Supply, Single/Dual (±) | 2.3V~5.5V ±1.15V~2.75V |
| Input Offset Voltage (Vos) | 5mV |
| Bandwidth | 6.5MHz |
| Unity Gain BW-Nom | 6500 kHz |
| Voltage Gain | 110dB |
| Power Supply Rejection Ratio (PSRR) | 92.04dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Voltage - Input Offset | 1mV |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 6.5MHz |
| Max I/O Voltage | 5mV |
| Height | 1.45mm |
| Length | 2.9mm |
| Width | 1.6mm |
| Thickness | 1.2mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA374AIDBVTG4 Overview
It is packaged in an SC-74A, SOT-753-case that protects the operational amplifiers from damage. Op amps are General Purpose types of amplifier on the chip. Upon delivery, op amp ic is packaged in a Tape & Reel (TR) case. It is estimated that there will be 5 terminations in the next few months. There are a total of 5 pins on this op amp. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. To be specific, this instrumentation amplifier is a type of Operational Amplifier. In total, the buffer amplifier consists of 5 pins. With regards to the offset voltage of the input, buffer amplifier is rated at 5mV. It is recommended that this electronic component be mounted using the Surface Mount mounting type. According to the manufacturer, this buffer op amp works well at -40°C~125°C , which is a good operating temperature. In order for this instrumentation amplifier to operate, the supply current needs to be between 585μA and 10 . It is recommended to keep the voltage gain at 110dB at all times. There are a total of 1 channels available on the op amps. In addition to outputting Rail-to-Rail signals, this op amp ic offers a number of other advantages. To pack the operational amplifier ics, TR is adopted as the packing method.
OPA374AIDBVTG4 Features
5 Pins
supply voltage of 5V
110dB voltage gain
Output Type: Rail-to-Rail
OPA374AIDBVTG4 Applications
There are a lot of Texas Instruments OPA374AIDBVTG4 Instrumentational OP Amps applications.
- Signal operation
- Polarized electrodes
- Portable media players
- MP3
- Television broadcasting equipment
- Radar
- Integrator circuits
- Video conversion and routing
- Video amplifiers
- Vehicle electronics
