banner_page

OPA376AIDRG4

50mA per Channel 0.2pA 76 dB Instrumentational OP Amps 2.2V~5.5V ±1.1V~2.75V OPA376 8 Pins 8-SOIC (0.154, 3.90mm Width)


  • Manufacturer: Texas Instruments
  • Nocochips NO: 815-OPA376AIDRG4
  • Package: 8-SOIC (0.154, 3.90mm Width)
  • Datasheet: -
  • Stock: 100
  • Description: 50mA per Channel 0.2pA 76 dB Instrumentational OP Amps 2.2V~5.5V ±1.1V~2.75V OPA376 8 Pins 8-SOIC (0.154, 3.90mm Width)(Kg)

Details

Tags

Parameters
Factory Lead Time 1 Week
Lifecycle Status ACTIVE (Last Updated: 1 week ago)
Mounting Type Surface Mount
Package / Case 8-SOIC (0.154, 3.90mm Width)
Surface Mount YES
Number of Pins 8
Operating Temperature -40°C~125°C
Packaging Tape & Reel (TR)
Series e-trim™
JESD-609 Code e4
Pbfree Code yes
Part Status Active
Moisture Sensitivity Level (MSL) 2 (1 Year)
Number of Terminations 8
ECCN Code EAR99
Terminal Finish Nickel/Palladium/Gold (Ni/Pd/Au)
Subcategory Operational Amplifier
Packing Method TR
Technology CMOS
Terminal Position DUAL
Terminal Form GULL WING
Peak Reflow Temperature (Cel) 260
Number of Functions 1
Supply Voltage 2.2V
Base Part Number OPA376
Pin Count 8
Output Type Rail-to-Rail
Power Supplies 2.5/5V
Number of Circuits 1
Operating Supply Current 760μA
Nominal Supply Current 950μA
Output Current 30mA
Slew Rate 2V/μs
Architecture VOLTAGE-FEEDBACK
Amplifier Type General Purpose
Common Mode Rejection Ratio 76 dB
Current - Input Bias 0.2pA
Voltage - Supply, Single/Dual (±) 2.2V~5.5V ±1.1V~2.75V
Output Current per Channel 50mA
Input Offset Voltage (Vos) 5μV
Bandwidth 5.5MHz
Unity Gain BW-Nom 5500 kHz
Voltage Gain 134dB
Low-Offset YES
Frequency Compensation YES
Supply Voltage Limit-Max 7V
Low-Bias YES
Micropower NO
Programmable Power NO
Max I/O Voltage 25μV
Power NO
Height 1.75mm
Length 4.9mm
Width 3.91mm
Thickness 1.58mm
Radiation Hardening No
RoHS Status ROHS3 Compliant
Lead Free Lead Free

OPA376AIDRG4 Overview


Op amp is packaged in 8-SOIC (0.154, 3.90mm Width) case. The instrumentation amplifier in this picture is of the General Purpose-type. A Tape & Reel (TR) case is used to deliver the buffer op amp. During the past two weeks, there have been close to 8 terminations. The total number of pins on linear amplifier is 8. Please take in mind that op amp should be run at 2.2V. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. There are 8 pins on this chip. In terms of the input offset voltage, instrumentation amplifier rates at 5μV. Surface Mount is the recommended mounting type of operational amplifiers. It is important to note that this linear amplifier works well at a temperature of -40°C~125°C when it comes to operating temperatureUsing a supply current of 760μA , this buffer op amp will be able to operate. The voltage gain should stay at 134dB. On this instrumentation amplifier, there are 1 circuits that are connected together. There are more than a few advantages to using this instrumentation amplifier, one of which is that it outputs Rail-to-Rail signals. A TR-shaped amplifier is used to pack the buffer amps. This buffer amplifier is assigned within the e-trim? series by its manufacturer.

OPA376AIDRG4 Features


8 Pins
supply voltage of 2.2V
134dB voltage gain
Output Type: Rail-to-Rail

OPA376AIDRG4 Applications


There are a lot of Texas Instruments OPA376AIDRG4 Instrumentational OP Amps applications.

  • Logarithmic operation circuits
  • Polarized electrodes
  • Signal operation
  • Proportional counter tubes
  • Fast A/D and D/A converters
  • Integrator circuits
  • Signal filtering
  • High-frequency data acquisition systems
  • Medical instruments
  • Automotive sensors

Write a review

Note: HTML is not translated!
    Bad           Good