Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 6 days ago) |
Contact Plating |
Gold |
Mounting Type |
Surface Mount |
Package / Case |
8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
Surface Mount |
YES |
Number of Pins |
8 |
Weight |
25.996513mg |
Operating Temperature |
-40°C~125°C |
Packaging |
Tape & Reel (TR) |
JESD-609 Code |
e4 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
2 (1 Year) |
Number of Terminations |
8 |
ECCN Code |
EAR99 |
Resistance |
10 TΩ |
Subcategory |
Other Telecom ICs |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
5V |
Terminal Pitch |
0.65mm |
Base Part Number |
OPA380 |
Pin Count |
8 |
Number of Elements |
1 |
Power Supplies |
3/5V |
Operating Supply Current |
7.5mA |
Slew Rate |
80V/μs |
Amplifier Type |
Transimpedance |
Common Mode Rejection Ratio |
100 dB |
Current - Input Bias |
3pA |
Voltage - Supply, Single/Dual (±) |
2.7V~5.5V |
Output Current per Channel |
150mA |
Input Offset Voltage (Vos) |
25μV |
Gain Bandwidth Product |
90MHz |
Voltage Gain |
130dB |
Power Supply Rejection Ratio (PSRR) |
112.4dB |
Voltage - Input Offset |
4μV |
Telecom IC Type |
TELECOM CIRCUIT |
Max I/O Voltage |
25μV |
Input Voltage Noise Density |
67nV/sqrt Hz |
Height |
1.07mm |
Length |
3mm |
Width |
3mm |
Thickness |
970μm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
OPA380AIDGKR Overview
Packaged in a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) case, the buffer op amp is ready to use. The instrumentation amplifier in this picture is of the Transimpedance-type. A Tape & Reel (TR) case is used to deliver the buffer op amp. It is estimated that there will be 8 terminations in the next few months. The total number of pins on linear amplifier is 8. I would like to remind you that this buffer op amp should be powered by an 5V battery. A type of Other Telecom ICs op amp ic can be identified by the fact that this is a type of Other Telecom ICs device. The op amp ic has an array of 8 pins on it. With regards to the offset voltage of the input, buffer amplifier is rated at 25μV. The mounting type that is recommended for this electrical part is Surface Mount. In terms of operating temperature, this instrumentation amplifier is well suited to a temperature range of -40°C~125°C. You can run this op amp ic on 7.5mA . Maintain 130dB as the voltage gain. The total number of elements in this buffer amplifier is 1. It is important that the op amp resistance stays within the range of 10 TΩ. Instrumentation amplifier uses a telecom IC type TELECOM CIRCUIT.
OPA380AIDGKR Features
8 Pins
supply voltage of 5V
130dB voltage gain
Resistance of 10 TΩ
OPA380AIDGKR Applications
There are a lot of Texas Instruments OPA380AIDGKR Instrumentational OP Amps applications.
- Micro signal measurement
- Portable electronic products powered by batteries
- Biopotential
- Comparator
- High-frequency data acquisition systems
- Navigation
- Video data acquisition
- Precision measurement
- Exponential operation circuits
- Test equipment