OPA4137P
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 6 days ago) |
| Mounting Type | Through Hole |
| Package / Case | 14-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 14 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Series | MicroAmplifier™ |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Terminal Position | DUAL |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Base Part Number | OPA4137 |
| Pin Count | 14 |
| Operating Supply Voltage | 18V |
| Number of Circuits | 4 |
| Operating Supply Current | 220μA |
| Nominal Supply Current | 220μA |
| Output Current | 60mA |
| Slew Rate | 3.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 74 dB |
| Current - Input Bias | 5pA |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±2.25V~18V |
| Output Current per Channel | 60mA |
| Input Offset Voltage (Vos) | 1.5mV |
| Bandwidth | 1MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 94dB |
| Average Bias Current-Max (IIB) | 0.0001μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.0001μA |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 1MHz |
| Max I/O Voltage | 3mV |
| Power | NO |
| Input Offset Current-Max (IIO) | 0.00005μA |
| Height | 5.08mm |
| Length | 19.3mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA4137P Overview
There is a 14-DIP (0.300, 7.62mm) case in which the instrumentation amplifier is packaged. There are two types of operational amplifiers in this circuit. There is a Tube case that is delivered with the instrumentation amplifiers. There is a growing number of terminations approaching the number of 14. A total of 14 pins are attached to buffer op amp. It would be helpful if you could remember that this op amp ic should be powered by an 15V battery. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. In total, the buffer amplifier consists of 14 pins. In terms of input offset voltage, operational amplifier rates 1.5mV. This electronic component is recommended to be mounted using the mounting type Through Hole. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about -40°C~85°C . As long as the supply current of the chip does not exceed 220μA, this op amp ic can operate. You should keep the voltage gain at 94dB for the time being. This op amp contains 4 circuits. The operating supply voltage of instrumentation amplifier is rated 18V voltage. MicroAmplifier? is the number that corresponds to the series of the buffer op amp.
OPA4137P Features
14 Pins
supply voltage of 15V
94dB voltage gain
OPA4137P Applications
There are a lot of Texas Instruments OPA4137P Instrumentational OP Amps applications.
- Digital cameras
- Automotive sensors
- Automation control systems
- Scintillation detectors
- Broadcasting
- Weighing systems
- Micro signal measurement
- pH (acidity)
- MP3
- Radar
