OPA4180IPW
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Base Part Number | OPA4180 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Number of Channels | 4 |
| Operating Supply Current | 450μA |
| Nominal Supply Current | 450μA |
| Slew Rate | 0.8V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | Zero-Drift |
| Common Mode Rejection Ratio | 104 dB |
| Current - Input Bias | 250pA |
| Max Input Voltage | 18V |
| Voltage - Supply, Single/Dual (±) | 4V~36V ±2V~18V |
| Output Current per Channel | 18mA |
| Input Offset Voltage (Vos) | 15μV |
| Bandwidth | 2MHz |
| Unity Gain BW-Nom | 2000 kHz |
| Voltage Gain | 120dB |
| Average Bias Current-Max (IIB) | 0.006μA |
| Power Supply Rejection Ratio (PSRR) | 140dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 20V |
| Low-Bias | NO |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.001μA |
| Programmable Power | NO |
| Neg Supply Voltage-Max (Vsup) | -20V |
| Nominal Gain Bandwidth Product | 2MHz |
| Max I/O Voltage | 75μV |
| Input Voltage Noise Density | 10nV/sqrt Hz |
| Height | 1.2mm |
| Length | 5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA4180IPW Overview
Packaging for the buffer amplifier is in the form of a 14-TSSOP (0.173, 4.40mm Width) case. A Zero-Drift-type buffer amplifier is shown here. There is a Tube case that is delivered with the instrumentation amplifiers. There is a growing number of terminations approaching the number of 14. A total of 14 pins are located on this board. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. 14 pins are included on the operational amplifiers. Op amp ic rates 15μV for input offset voltage. This electrical part should be mounted using type Surface Mount. In terms of operating temperature, this instrumentation amplifier is well suited to a temperature range of -40°C~125°C. An 450μA volt supply current is needed for this linear amplifier to operate. 120dB should remain the voltage gain. Buffer op amp is equipped with 4 channels on the device. One of its many advantages is that buffer op amp outputs Rail-to-Rail signals.
OPA4180IPW Features
14 Pins
120dB voltage gain
Output Type: Rail-to-Rail
OPA4180IPW Applications
There are a lot of Texas Instruments OPA4180IPW Instrumentational OP Amps applications.
- Information processing
- Hand-held batteries
- High speed sample
- Cinema or auditorium audio system
- Radiation thermometry transducers
- Ultrasound transducers
- Gaming industry
- Inverse/same-phase proportional circuit
- Polarized electrodes
- Non-polarized electrodes
