OPA4188AID
| Parameters | |
|---|---|
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Terminal Pitch | 1.27mm |
| Base Part Number | OPA4188 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 18V |
| Number of Channels | 4 |
| Operating Supply Current | 415μA |
| Nominal Supply Current | 475μA |
| Output Current | 18mA |
| Slew Rate | 0.8V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 120 dB |
| Current - Input Bias | 160pA |
| Voltage - Supply, Single/Dual (±) | ±2V~18V |
| Output Current per Channel | 18mA |
| Input Offset Voltage (Vos) | 6μV |
| Bandwidth | 2MHz |
| Unity Gain BW-Nom | 2000 kHz |
| Voltage Gain | 136dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 20V |
| Low-Bias | NO |
| Micropower | YES |
| Max Frequency | 1MHz |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 2MHz |
| Power | NO |
| Input Offset Current-Max (IIO) | 0.0028μA |
| Height | 1.75mm |
| Length | 8.65mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
OPA4188AID Overview
A 14-SOIC (0.154, 3.90mm Width) case is used to package the op amp. There are two types of operational amplifiers in this circuit. In the case of Tube cases, linear amplifier will be delivered. There have been a total of 14 terminations over the past year. In this case, there are 14 pins on the board. In order to be more specific, this instrumentation amplifier is one of the types of Operational Amplifier devices. 14 pins are included on the operational amplifiers. Op amp rates 6μV as input offset voltage. This electrical part should be mounted using type Surface Mount. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about -40°C~125°C . As long as the supply current of the chip does not exceed 415μA, this op amp ic can operate. There should be no change in the voltage gain. There are a total of 4 channels available on the op amps. One of the advantages of this op amp is that it outputs Rail-to-Rail signals, which is one of its many advantages. The operating supply voltage of the buffer op amp is rated at 18V.
OPA4188AID Features
14 Pins
136dB voltage gain
Output Type: Rail-to-Rail
OPA4188AID Applications
There are a lot of Texas Instruments OPA4188AID Instrumentational OP Amps applications.
- Signal amplification
- Navigation
- Laptop
- Blood pressure sensors
- Active probe
- Hand-held batteries
- Portable docking station
- single/dual op amp sum and difference circuits
- Vehicle electronics
- Test equipment
