OPA4340UA
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 14 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Series | MicroAmplifier™ |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Base Part Number | OPA4340 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Power Supplies | 3/5V |
| Number of Channels | 4 |
| Operating Supply Current | 750μA |
| Nominal Supply Current | 3.8mA |
| Slew Rate | 6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 0.2pA |
| Voltage - Supply, Single/Dual (±) | 2.5V~5.5V |
| Output Current per Channel | 50mA |
| Input Offset Voltage (Vos) | 150μV |
| Bandwidth | 5.5MHz |
| Unity Gain BW-Nom | 5500 kHz |
| Voltage Gain | 124dB |
| Average Bias Current-Max (IIB) | 0.00006μA |
| Power Supply Rejection Ratio (PSRR) | 90.46dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 5.5V |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.00001μA |
| Programmable Power | NO |
| Max I/O Voltage | 500μV |
| Input Offset Current-Max (IIO) | 0.00001μA |
| Height | 1.75mm |
| Length | 8.65mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA4340UA Overview
There is a 14-SOIC (0.154, 3.90mm Width) case in which the instrumentation amplifier is packaged. A General Purpose-type buffer amplifier is shown here. It comes in a Tube case, which protects instrumentation amplifier from damage during delivery. During the past two weeks, there have been close to 14 terminations. In total, there are 14 pins on this op amp ic. Please take in mind that this instrumentation amplifier should be run at 5V. Instrumentation amplifier is a part of Operational Amplifier. 14 pins are available on the instrumentation amplifier. Op amp rates 150μV as input offset voltage. For this electrical component, Surface Mount is the recommended mounting type. It is important to note that this linear amplifier works well at a temperature of -40°C~85°C when it comes to operating temperatureIn order for this instrumentation amplifier to operate, the supply current needs to be between 750μA and 10 . There should be no change in the voltage gain. As far as the device is concerned, buffer amplifier has 4 channels. One of the many benefits of this op amp ic is that it emits Rail-to-Rail signals. The MicroAmplifier? indicates the series number of the op amp.
OPA4340UA Features
14 Pins
supply voltage of 5V
124dB voltage gain
Output Type: Rail-to-Rail
OPA4340UA Applications
There are a lot of Texas Instruments OPA4340UA Instrumentational OP Amps applications.
- Industrial applications including automation
- Ultrasound transducers
- Inverse/same-phase proportional circuit
- Voltage regulation circuit
- Semiconductor detectors
- Television broadcasting equipment
- Switching amplifier
- Navigation
- Logarithmic operation circuits
- Measurements of Wheatstone bridge
