OPA4354AIDR
| Parameters | |
|---|---|
| Bias Current-Max (IIB) @25C | 0.00005μA |
| Programmable Power | NO |
| Max I/O Voltage | 8mV |
| Input Offset Current-Max (IIO) | 0.00005μA |
| Height | 1.75mm |
| Length | 8.65mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 14 |
| Weight | 129.387224mg |
| Operating Temperature | -40°C~125°C |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Base Part Number | OPA4354 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Number of Channels | 4 |
| Operating Supply Current | 4.9mA |
| Nominal Supply Current | 24mA |
| Slew Rate | 150V/μs |
| Amplifier Type | Voltage Feedback |
| Common Mode Rejection Ratio | 56 dB |
| Current - Input Bias | 3pA |
| Voltage - Supply, Single/Dual (±) | 2.5V~5.5V ±1.25V~2.75V |
| Output Current per Channel | 100mA |
| Input Offset Voltage (Vos) | 8mV |
| Bandwidth | 100MHz |
| Unity Gain BW-Nom | 100000 kHz |
| Voltage Gain | 110dB |
| Average Bias Current-Max (IIB) | 0.00005μA |
| Power Supply Rejection Ratio (PSRR) | 73.98dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7.5V |
| Voltage - Input Offset | 2mV |
| Settling Time | 30 ns |
| Low-Bias | YES |
| Micropower | NO |
| -3db Bandwidth | 250MHz |
OPA4354AIDR Overview
Packaged in a 14-SOIC (0.154, 3.90mm Width) case, the buffer op amp is ready to use. Op amps are Voltage Feedback types of amplifier on the chip. Instrumentation amplifier is delivered in a Cut Tape (CT) case. We are approaching the 14h termination of the year. In this case, there are 14 pins on the board. As a reminder, this buffer op amp should be powered by 5V battery and that the battery should be inserted in the amplifier. To be specific, this instrumentation amplifier is a type of Operational Amplifier. A total of 14 pins are present on the instrumentation amplifier. In terms of the input offset voltage, instrumentation amplifier rates at 8mV. For this electronic part, it is recommended that you mount it with type Surface Mount. With regard to operating temperature, op amp ranges -40°C~125°C. An 4.9mA volt supply current is needed for this linear amplifier to operate. Voltage gain should remain at 110dB. As far as the device is concerned, buffer amplifier has 4 channels. One of its many advantages is that buffer op amp outputs Rail-to-Rail signals. For the packing of the instrumentation amplifier, TR is adopted.
OPA4354AIDR Features
14 Pins
supply voltage of 5V
110dB voltage gain
Output Type: Rail-to-Rail
OPA4354AIDR Applications
There are a lot of Texas Instruments OPA4354AIDR Instrumentational OP Amps applications.
- Semiconductor detectors
- ECG equipment
- Addition operation circuits
- Wireless base stations
- Displayers for aircraft and air transportation control systems
- earphone
- Fission chambers
- High input resistance broadband
- Laptop
- Industrial control system
