OPA4374AIPWRG4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Base Part Number | OPA4374 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Number of Elements | 4 |
| Power Supplies | 3/5V |
| Operating Supply Current | 585μA |
| Nominal Supply Current | 3mA |
| Slew Rate | 5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 0.5pA |
| Voltage - Supply, Single/Dual (±) | 2.3V~5.5V ±1.15V~2.75V |
| Input Offset Voltage (Vos) | 5mV |
| Bandwidth | 6.5MHz |
| Unity Gain BW-Nom | 6500 kHz |
| Voltage Gain | 110dB |
| Average Bias Current-Max (IIB) | 0.00001μA |
| Power Supply Rejection Ratio (PSRR) | 92.04dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Voltage - Input Offset | 1mV |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.00001μA |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 6.5MHz |
| Max I/O Voltage | 5mV |
| Input Offset Current-Max (IIO) | 0.00001μA |
| Height | 1.2mm |
| Length | 5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA4374AIPWRG4 Overview
There is a 14-TSSOP (0.173, 4.40mm Width) case in which the instrumentation amplifier is packaged. An op amp of this type is a General Purpose-type. A Tape & Reel (TR) case is used to deliver the buffer op amp. There have been a total of 14 terminations over the past year. A total of 14 pins are attached to buffer op amp. I would like to remind you that this buffer op amp should be powered by an 5V battery. A type of Operational Amplifier buffer op amp is what this device is specifically, to be more precise. 14 pins are included on the operational amplifiers. In terms of the input offset voltage, instrumentation amplifier rates at 5mV. It is recommended that this electronic component be mounted using the Surface Mount mounting type. In terms of operating temperatures, this buffer amplifier works very well at a temperature of around -40°C~125°C . Operational amplifier can operate supply current at 585μA. 110dB should be the voltage gain. This op amp ic outputs Rail-to-Rail signals, which is one of the many benefits it has. There are 4 elements in total in this linear amplifier. For the packing of the instrumentation amplifier, TR is adopted.
OPA4374AIPWRG4 Features
14 Pins
supply voltage of 5V
110dB voltage gain
Output Type: Rail-to-Rail
OPA4374AIPWRG4 Applications
There are a lot of Texas Instruments OPA4374AIPWRG4 Instrumentational OP Amps applications.
- Multimedia playback equipment
- Measurements of Wheatstone bridge
- Industrial applications including automation
- Inverse/same-phase proportional circuit
- Ultrasound transducers
- Scintillation detectors
- Signal amplification
- Video amplifiers
- Band-stop filter
- High-frequency data acquisition systems
