OPA4374AIPWT
| Parameters | |
|---|---|
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Base Part Number | OPA4374 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Number of Elements | 4 |
| Power Supplies | 3/5V |
| Operating Supply Current | 585μA |
| Nominal Supply Current | 3mA |
| Slew Rate | 5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 0.5pA |
| Voltage - Supply, Single/Dual (±) | 2.3V~5.5V ±1.15V~2.75V |
| Input Offset Voltage (Vos) | 5mV |
| Bandwidth | 6.5MHz |
| Unity Gain BW-Nom | 6500 kHz |
| Voltage Gain | 110dB |
| Average Bias Current-Max (IIB) | 0.00001μA |
| Power Supply Rejection Ratio (PSRR) | 92.04dB |
| Low-Offset | NO |
| Frequency Compensation | NO |
| Supply Voltage Limit-Max | 7V |
| Voltage - Input Offset | 1mV |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.00001μA |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 6.5MHz |
| Max I/O Voltage | 5mV |
| Input Offset Current-Max (IIO) | 0.00001μA |
| Height | 1.2mm |
| Length | 5mm |
| Width | 4.4mm |
| Thickness | 1mm |
OPA4374AIPWT Overview
Packaged in a 14-TSSOP (0.173, 4.40mm Width) case, the buffer op amp is ready to use. An op amp ic of the General Purpose type. The case in which buffer amplifier is delivered is called a Tape & Reel (TR) case. We are approaching the 14h termination of the year. Buffer amplifier has a total of 14 pins. The linear amplifier should be run at 5V at all times, so please keep that in mind when using it. In more specific terms, this linear amplifier can be categoriOperational Amplifiered as a Operational Amplifier-type device. In total, the buffer amplifier consists of 14 pins. With regard to input offset voltage, instrumentation amplifier is rated at 5mV. The mounting type that is recommended for this electrical part is Surface Mount. With regard to operating temperature, op amp ranges -40°C~125°C. An 585μA volt supply current is needed for this linear amplifier to operate. 110dB should remain the voltage gain. This op amp ic outputs Rail-to-Rail signals, which is one of the many benefits it has. 4 elements make up the design of this buffer amplifier. The linear amplifier is packaged by using a TR axis.
OPA4374AIPWT Features
14 Pins
supply voltage of 5V
110dB voltage gain
Output Type: Rail-to-Rail
OPA4374AIPWT Applications
There are a lot of Texas Instruments OPA4374AIPWT Instrumentational OP Amps applications.
- Polarized electrodes
- Navigation
- Commercial audio systems
- Test equipment
- Home audio systems
- Power control
- Industrial applications including automation
- Semiconductor detectors
- High/low-pass filter circuit
- Medical instruments
