OPA452FAKTWT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | TO-263-8, D2Pak (7 Leads + Tab), TO-263CA |
| Number of Pins | 7 |
| Operating Temperature | -40°C~125°C |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 7 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Terminal Position | SINGLE |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 1 |
| Supply Voltage | 40V |
| Base Part Number | OPA452 |
| Pin Count | 7 |
| Number of Channels | 1 |
| Operating Supply Current | 5.5mA |
| Nominal Supply Current | 6.5mA |
| Output Current | 50mA |
| Slew Rate | 10V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 86 dB |
| Current - Input Bias | 7pA |
| Voltage - Supply, Single/Dual (±) | 20V~80V ±10V~40V |
| Output Current per Channel | 50mA |
| Input Offset Voltage (Vos) | 3mV |
| Bandwidth | 1.8MHz |
| Neg Supply Voltage-Nom (Vsup) | -40V |
| Unity Gain BW-Nom | 1800 kHz |
| Voltage Gain | 110dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 40V |
| Voltage - Input Offset | 1mV |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Dual Supply Voltage | 28V |
| Neg Supply Voltage-Max (Vsup) | -40V |
| Power | YES |
| Height | 4.65mm |
| Length | 10.1mm |
| Width | 8.89mm |
| Thickness | 4.44mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA452FAKTWT Overview
The linear amplifier is packaged in a TO-263-8, D2Pak (7 Leads + Tab), TO-263CA case. An op amp of this type is a General Purpose-type. A Cut Tape (CT) case is used to deliver the buffer op amp. There have been a total of 7 terminations over the past year. A total of 7 pins are located on this board. Please take in mind that op amp should be run at 40V. In order to be more specific, this instrumentation amplifier is one of the types of Operational Amplifier devices. 7 pins are available on the instrumentation amplifier. In terms of the input offset voltage, instrumentation amplifier rates at 3mV. This electronic part is recommended for mounting type Surface Mount. In terms of operating temperatures, this buffer amplifier works very well at a temperature of around -40°C~125°C . The buffer amplifier is capable of operating from a supply current of 5.5mA . There should be no change in the voltage gain at 110dB. The op amp ic has 1 channels on it. To pack the operational amplifier ics, TR is adopted as the packing method.
OPA452FAKTWT Features
7 Pins
supply voltage of 40V
110dB voltage gain
OPA452FAKTWT Applications
There are a lot of Texas Instruments OPA452FAKTWT Instrumentational OP Amps applications.
- Large motor controllers
- Semiconductor detectors
- Active probe
- Micro signal measurement
- Automatic control
- Weighing systems
- Band-pass filter
- Exponential operation circuits
- Test and measurement instruments
- Radiation thermometry transducers
