OPA454AIDDAG4
| Parameters | |
|---|---|
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 100 dB |
| Current - Input Bias | 1.4pA |
| Voltage - Supply, Single/Dual (±) | 10V~100V ±5V~50V |
| Output Current per Channel | 150mA |
| Input Offset Voltage (Vos) | 4mV |
| Neg Supply Voltage-Nom (Vsup) | -50V |
| Unity Gain BW-Nom | 2500 kHz |
| Voltage Gain | 130dB |
| Power Supply Rejection Ratio (PSRR) | 92.04dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 60V |
| Voltage - Input Offset | 200μV |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 2.5MHz |
| Max I/O Voltage | 4mV |
| Wideband | NO |
| Height | 1.7mm |
| Length | 4.89mm |
| Width | 3.9mm |
| Thickness | 1.48mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-PowerSOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 50V |
| Base Part Number | OPA454 |
| Pin Count | 8 |
| Operating Supply Voltage | 50V |
| Number of Elements | 1 |
| Operating Supply Current | 3.2mA |
| Nominal Supply Current | 4mA |
| Output Current | 50mA |
| Slew Rate | 13V/μs |
| Architecture | VOLTAGE-FEEDBACK |
OPA454AIDDAG4 Overview
A 8-PowerSOIC (0.154, 3.90mm Width) case is used to package the op amp. Op amps are General Purpose types of amplifier on the chip. Linear amplifier is delivered in a Tube case. It is estimated that there will be 8 terminations in the next few months. There are a total of 8 pins on this op amp. I would like to remind you that this buffer op amp should be powered by an 50V battery. Instrumentation amplifier is a part of Operational Amplifier. 8 pins are located on the operational amplifiers. In terms of the input offset voltage, instrumentation amplifier rates at 4mV. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. With regard to operating temperature, op amp ranges -40°C~85°C. This op amp can operate from a supply current at 3.2mA. You should keep the voltage gain at 130dB for the time being. Op amp has total of 1 elements. The operating supply voltage of instrumentation amplifier is rated 50V voltage.
OPA454AIDDAG4 Features
8 Pins
supply voltage of 50V
130dB voltage gain
OPA454AIDDAG4 Applications
There are a lot of Texas Instruments OPA454AIDDAG4 Instrumentational OP Amps applications.
- Fission chambers
- Power control
- Inverse/same-phase proportional circuit
- Multimedia playback equipment
- Image computer boards
- Comparator
- Portable docking station
- Industrial control system
- RF cable systems
- High/low-pass filter circuit
