OPA549TG3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mounting Type | Through Hole |
| Package / Case | TO-220-11 (Formed Leads) |
| Surface Mount | NO |
| Number of Pins | 11 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 11 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Terminal Position | ZIG-ZAG |
| Number of Functions | 1 |
| Supply Voltage | 30V |
| Base Part Number | OPA549 |
| Pin Count | 3 |
| Operating Supply Voltage | 30V |
| Power Supplies | +-4/+-30/8/60V |
| Number of Channels | 1 |
| Operating Supply Current | 26mA |
| Nominal Supply Current | 35mA |
| Output Current | 8A |
| Slew Rate | 9V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | Power |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 100nA |
| Voltage - Supply, Single/Dual (±) | 8V~60V ±4V~30V |
| Output Current per Channel | 10A |
| Input Offset Voltage (Vos) | 5mV |
| Bandwidth | 900 kHz |
| Neg Supply Voltage-Nom (Vsup) | -30V |
| Unity Gain BW-Nom | 900 kHz |
| Voltage Gain | 110dB |
| Average Bias Current-Max (IIB) | 0.5μA |
| Power Supply Rejection Ratio (PSRR) | 92.04dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 1mV |
| Low-Bias | NO |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.5μA |
| Programmable Power | YES |
| Dual Supply Voltage | 9V |
| Nominal Gain Bandwidth Product | 900 kHz |
| Max I/O Voltage | 5mV |
| Input Offset Current-Max (IIO) | 0.05μA |
| Height | 4.62mm |
| Length | 20.02mm |
| Width | 10.7mm |
| Thickness | 4.5mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA549TG3 Overview
There is a TO-220-11 (Formed Leads) case in which the instrumentation amplifier is packaged. There are two types of operational amplifiers in this circuit. The case in which buffer amplifier is delivered is called a Tube case. During the past two weeks, there have been close to 11 terminations. The pins on this board total to 3 in total. It would be helpful if you could remember that this op amp ic should be powered by an 30V battery. A type of Operational Amplifier buffer op amp is what this device is specifically, to be more precise. It has 11 pins that make up the linear amplifier. With regards to the offset voltage of the input, buffer amplifier is rated at 5mV. This electronic part is best mounted with type Through Hole. Regarding the operating temperature of this device, instrumentation amplifier performs well at a temperature of -40°C~85°C . As long as the supply current of the chip does not exceed 26mA, this op amp ic can operate. 110dB should remain the voltage gain. Buffer op amp is equipped with 1 channels on the device. The operating supply voltage of the buffer op amp is rated at 30V.
OPA549TG3 Features
3 Pins
supply voltage of 30V
110dB voltage gain
OPA549TG3 Applications
There are a lot of Texas Instruments OPA549TG3 Instrumentational OP Amps applications.
- RF cable systems
- PDA
- Test and measurement instruments
- Laptop
- Automotive sensors
- MP3
- High/low-pass filter circuit
- ECG equipment
- Switching amplifier
- Communication device
