OPA551FAKTWT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | TO-263-8, D2Pak (7 Leads + Tab), TO-263CA |
| Number of Pins | 7 |
| Operating Temperature | -40°C~125°C |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 7 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Terminal Position | SINGLE |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 30V |
| Base Part Number | OPA551 |
| Pin Count | 7 |
| Power Supplies | +-4/+-30/8/60V |
| Number of Channels | 1 |
| Operating Supply Current | 7mA |
| Nominal Supply Current | 8.5mA |
| Output Current | 200mA |
| Quiescent Current | 4A |
| Slew Rate | 15V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 92 dB |
| Current - Input Bias | 20pA |
| Voltage - Supply, Single/Dual (±) | 8V~60V ±4V~30V |
| Output Current per Channel | 200mA |
| Input Offset Voltage (Vos) | 3mV |
| Bandwidth | 3MHz |
| Neg Supply Voltage-Nom (Vsup) | -30V |
| Unity Gain BW-Nom | 3000 kHz |
| Voltage Gain | 126dB |
| Power Supply Rejection Ratio (PSRR) | 100dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 30V |
| Voltage - Input Offset | 1mV |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Neg Supply Voltage-Max (Vsup) | -30V |
| Height | 4.65mm |
| Length | 10.1mm |
| Width | 8.89mm |
| Thickness | 4.44mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA551FAKTWT Overview
In order to protect the op amps, a TO-263-8, D2Pak (7 Leads + Tab), TO-263CA case is used. There are two types of operational amplifiers in this circuit. The case in which buffer amplifier is delivered is called a Cut Tape (CT) case. A total of 7 terminations have been reported in the past few weeks. The pins on this board total to 7 in total. Please take in mind that this instrumentation amplifier should be run at 30V. Instrumentation amplifier is a part of Operational Amplifier. 7 pins are located on the operational amplifiers. Regarding input offset voltage, op amp rates 3mV. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. In relation to the operating temperature of this buffer op amp, it works well at an average of -40°C~125°C . It is possible to operate this buffer amplifier from a supply current of 7mA . You should keep the voltage gain at 126dB for the time being. Buffer op amp is equipped with 1 channels on the device. An buffer amplifier is packed in a TR-shape according to the design. There is an 4A quiescent current in linear amplifier.
OPA551FAKTWT Features
7 Pins
supply voltage of 30V
126dB voltage gain
OPA551FAKTWT Applications
There are a lot of Texas Instruments OPA551FAKTWT Instrumentational OP Amps applications.
- Weak signal detection
- Power generator
- Power transmission
- Portable docking station
- Vehicle electronics
- Video conversion and routing
- Signal operation
- Communication device
- Polarized electrodes
- Mobile phone
