OPA551FAKTWTG3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | TO-263-8, D2Pak (7 Leads + Tab), TO-263CA |
| Number of Pins | 7 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 7 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Terminal Position | SINGLE |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 30V |
| Base Part Number | OPA551 |
| Pin Count | 7 |
| Power Supplies | +-4/+-30/8/60V |
| Number of Channels | 1 |
| Operating Supply Current | 7mA |
| Nominal Supply Current | 8.5mA |
| Output Current | 200mA |
| Slew Rate | 15V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 92 dB |
| Current - Input Bias | 20pA |
| Voltage - Supply, Single/Dual (±) | 8V~60V ±4V~30V |
| Output Current per Channel | 200mA |
| Input Offset Voltage (Vos) | 3mV |
| Bandwidth | 3MHz |
| Neg Supply Voltage-Nom (Vsup) | -30V |
| Unity Gain BW-Nom | 3000 kHz |
| Voltage Gain | 126dB |
| Power Supply Rejection Ratio (PSRR) | 100dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 30V |
| Voltage - Input Offset | 1mV |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Neg Supply Voltage-Max (Vsup) | -30V |
| Height | 4.65mm |
| Length | 10.1mm |
| Width | 8.89mm |
| Thickness | 4.44mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA551FAKTWTG3 Overview
In the package, you will find a TO-263-8, D2Pak (7 Leads + Tab), TO-263CA-case to contain the op amp ic. General Purpose-type instrumentation amplifiers are used in this application. Linear amplifier is delivered in a Tape & Reel (TR) case. During the past two weeks, there have been close to 7 terminations. Buffer amplifier has a total of 7 pins on it. It would be helpful if you could remember that this op amp ic should be powered by an 30V battery. It should be noted that this type of buffer amplifier is exactly what is known as a Operational Amplifier device. The buffer op amp includes 7 pins. In terms of the input offset voltage, instrumentation amplifier rates at 3mV. This electrical part should be mounted using type Surface Mount. The buffer amplifier functions well at -40°C~125°C as far as operating temperature is concerned. This op amp can operate from a supply current at 7mA. Keeping the voltage gain at 126dB is the best course of action. There are a total of 1 channels available on the op amps. To pack the operational amplifier ics, TR is adopted as the packing method.
OPA551FAKTWTG3 Features
7 Pins
supply voltage of 30V
126dB voltage gain
OPA551FAKTWTG3 Applications
There are a lot of Texas Instruments OPA551FAKTWTG3 Instrumentational OP Amps applications.
- Division circuits
- Exponential operation circuits
- Broadcasting
- High-frequency data acquisition systems
- Proportional counter tubes
- Multimedia playback equipment
- Laptop
- High gain DC amplifier
- Tablets
- Video data acquisition
