OPA551UA/2K5
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Contact Plating | Gold |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 30V |
| Base Part Number | OPA551 |
| Pin Count | 8 |
| Number of Channels | 1 |
| Operating Supply Current | 7mA |
| Nominal Supply Current | 8.5mA |
| Output Current | 200mA |
| Slew Rate | 15V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 92 dB |
| Current - Input Bias | 20pA |
| Voltage - Supply, Single/Dual (±) | 8V~60V ±4V~30V |
| Output Current per Channel | 200mA |
| Input Offset Voltage (Vos) | 3mV |
| Bandwidth | 3MHz |
| Neg Supply Voltage-Nom (Vsup) | -30V |
| Unity Gain BW-Nom | 3000 kHz |
| Voltage Gain | 126dB |
| Power Supply Rejection Ratio (PSRR) | 100dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 30V |
| Voltage - Input Offset | 1mV |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Neg Supply Voltage-Max (Vsup) | -30V |
| Nominal Gain Bandwidth Product | 3MHz |
| Max I/O Voltage | 3mV |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA551UA/2K5 Overview
A 8-SOIC (0.154, 3.90mm Width) case is used to package the op amp. An op amp ic of the General Purpose type. There is a Tape & Reel (TR) case that is delivered with the instrumentation amplifiers. During the past two weeks, there have been close to 8 terminations. In this case, there are 8 pins on the board. It would be helpful if you could remember that this op amp ic should be powered by an 30V battery. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. Linear amplifier includes 8 pins. Regarding input offset voltage, op amp rates 3mV. For this electronic part, it is recommended that you mount it with type Surface Mount. It is important to note that this linear amplifier works well at a temperature of -40°C~125°C when it comes to operating temperatureOperational amplifier can operate supply current at 7mA. Maintain 126dB as the voltage gain. There are 1 channels on the operational amplifiers. For the packing of the instrumentation amplifier, TR is adopted.
OPA551UA/2K5 Features
8 Pins
supply voltage of 30V
126dB voltage gain
OPA551UA/2K5 Applications
There are a lot of Texas Instruments OPA551UA/2K5 Instrumentational OP Amps applications.
- Home audio systems
- Thermocouples
- Weighing systems
- Signal amplification
- Hand-held batteries
- Communication
- Subtraction operation circuits
- PDA
- High gain DC amplifier
- Radiation thermometry transducers
