OPA561PWPG4
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 20-PowerTSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 20 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Part Status | Not For New Designs |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Base Part Number | OPA561 |
| Pin Count | 20 |
| Operating Supply Voltage | 15V |
| Number of Channels | 1 |
| Operating Supply Current | 50mA |
| Nominal Supply Current | 60mA |
| Output Current | 1.2A |
| Slew Rate | 50V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 10pA |
| Voltage - Supply, Single/Dual (±) | 7V~15V ±3.5V~7.5V |
| Output Current per Channel | 1.2A |
| Input Offset Voltage (Vos) | 20mV |
| Bandwidth | 17MHz |
| Unity Gain BW-Nom | 17000 kHz |
| Voltage Gain | 100dB |
| Power Supply Rejection Ratio (PSRR) | 92.04dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 1mV |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | YES |
| Dual Supply Voltage | 5V |
| Nominal Gain Bandwidth Product | 17MHz |
| Max I/O Voltage | 20mV |
| Height | 1.15mm |
| Length | 6.5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA561PWPG4 Overview
Op amp is packaged in 20-PowerTSSOP (0.173, 4.40mm Width) case. A General Purpose-type buffer amplifier is shown here. Upon delivery, op amp ic is packaged in a Tube case. The number of terminations approaches 20. In total, there are 20 pins on this op amp ic. I would like to remind you that this buffer op amp should be powered by an 15V battery. In more specific terms, this linear amplifier can be categoriOperational Amplifiered as a Operational Amplifier-type device. 20 pins are located on the operational amplifiers. As far as the input offset voltage is concerned, linear amplifier rates at 20mV. The mounting type that is recommended for this electrical part is Surface Mount. With regard to operating temperature, op amp ranges -40°C~125°C. It is possible to operate this buffer amplifier from a supply current of 50mA . Keeping the voltage gain at 100dB is the best course of action. There are a total of 1 channels available on the op amps. The operating supply voltage of instrumentation amplifier is rated 15V voltage.
OPA561PWPG4 Features
20 Pins
supply voltage of 15V
100dB voltage gain
OPA561PWPG4 Applications
There are a lot of Texas Instruments OPA561PWPG4 Instrumentational OP Amps applications.
- Hand-held batteries
- Gaming industry
- Radar
- Differentiator circuits
- Band-pass filter
- Automatic control
- Professional videography
- Portable media players
- Portable docking station
- Measurements of Wheatstone bridge
