OPA564AIDWD
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) Exposed Pad |
| Surface Mount | YES |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 12V |
| Base Part Number | OPA564 |
| Pin Count | 20 |
| Operating Supply Voltage | 12V |
| Number of Elements | 1 |
| Operating Supply Current | 39mA |
| Nominal Supply Current | 50mA |
| Output Current | 1.5A |
| Slew Rate | 40V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 10pA |
| Voltage - Supply, Single/Dual (±) | 7V~24V ±3.5V~12V |
| Output Current per Channel | 1.5A |
| Input Offset Voltage (Vos) | 20mV |
| Neg Supply Voltage-Nom (Vsup) | -12V |
| Unity Gain BW-Nom | 17000 kHz |
| Voltage Gain | 108dB |
| Power Supply Rejection Ratio (PSRR) | 100dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 2mV |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 17MHz |
| Max I/O Voltage | 20mV |
| Wideband | NO |
| Height | 2.65mm |
| Length | 12.82mm |
| Width | 7.52mm |
| Thickness | 2.35mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA564AIDWD Overview
In the package, you will find a 20-SOIC (0.295, 7.50mm Width) Exposed Pad-case to contain the op amp ic. There are two types of operational amplifiers in this circuit. In the case of Tube cases, linear amplifier will be delivered. The number of terminations is approaching the 20 mark. There are a total of 20 pins on this op amp. It would be helpful if you could remember that this op amp ic should be powered by an 12V battery. In more specific terms, this linear amplifier can be categoriOperational Amplifiered as a Operational Amplifier-type device. The op amp ic has an array of 20 pins on it. Op amp rates 20mV as input offset voltage. For this electrical component, Surface Mount is the recommended mounting type. In terms of operating temperatures, this buffer amplifier works very well at a temperature of around -40°C~85°C . An 39mA volt supply current is needed for this linear amplifier to operate. Voltage gain should remain at 108dB. There is an operating supply voltage rating of 1 for this operational amplifier, which is rated at the manufacturer. The operating supply voltage of the buffer op amp is rated at 12V.
OPA564AIDWD Features
20 Pins
supply voltage of 12V
108dB voltage gain
OPA564AIDWD Applications
There are a lot of Texas Instruments OPA564AIDWD Instrumentational OP Amps applications.
- Scintillation detectors
- High/low-pass filter circuit
- Polarized electrodes
- Medical imaging
- Differentiator circuits
- Tablets
- Logarithmic operation circuits
- Precision measurement
- Hand-held batteries
- Power control
