OPA627AU/2K5
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Weight | 75.891673mg |
| Operating Temperature | -25°C~85°C |
| Packaging | Tape & Reel (TR) |
| Series | Difet® |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Max Power Dissipation | 1W |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Base Part Number | OPA627 |
| Pin Count | 8 |
| Number of Channels | 1 |
| Operating Supply Current | 7mA |
| Nominal Supply Current | 7.5mA |
| Power Dissipation | 1W |
| Slew Rate | 55V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 100 dB |
| Current - Input Bias | 2pA |
| Voltage - Supply, Single/Dual (±) | 9V~36V ±4.5V~18V |
| Output Current per Channel | 45mA |
| Input Offset Voltage (Vos) | 500μV |
| Bandwidth | 16MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 16000 kHz |
| Voltage Gain | 116dB |
| Average Bias Current-Max (IIB) | 0.002μA |
| Power Supply Rejection Ratio (PSRR) | 100dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Voltage - Input Offset | 130μV |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Dual Supply Voltage | 15V |
| Nominal Gain Bandwidth Product | 16MHz |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA627AU/2K5 Overview
In order to protect the op amps, a 8-SOIC (0.154, 3.90mm Width) case is used. This is a General Purpose type op amp. A Tape & Reel (TR) case is used for delivering the op amp. During the past two weeks, there have been close to 8 terminations. Buffer amplifier has a total of 8 pins on it. Please take in mind that this instrumentation amplifier should be run at 15V. It should be noted that this type of buffer amplifier is exactly what is known as a Operational Amplifier device. 8 pins are available on the instrumentation amplifier. As far as the input offset voltage is concerned, linear amplifier rates at 500μV. Surface Mount is the recommended mounting type for this linear amplifier. It is important to note that this linear amplifier works well at a temperature of -25°C~85°C when it comes to operating temperatureIn order for this instrumentation amplifier to operate, the supply current needs to be between 7mA and 10 . 116dB should remain the voltage gain. Instrumentation amplifier has 1 channels on it. The instrumentation amplifier is packed in the form of TR. Buffer op amp series numbers are indicated by the Difet?.
OPA627AU/2K5 Features
8 Pins
supply voltage of 15V
116dB voltage gain
OPA627AU/2K5 Applications
There are a lot of Texas Instruments OPA627AU/2K5 Instrumentational OP Amps applications.
- Active probe
- Portable electronic products powered by batteries
- Band-pass filter
- Biopotential
- Medical imaging
- Fast A/D and D/A converters
- Multiplication circuits
- Displayers for aircraft and air transportation control systems
- Television
- Proportional counter tubes
