OPA659IDRBT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-VDFN Exposed Pad |
| Surface Mount | YES |
| Number of Pins | 8 |
| Weight | 24.012046mg |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 6V |
| Terminal Pitch | 0.65mm |
| Base Part Number | OPA659 |
| Pin Count | 8 |
| Power Supplies | +-3.5/+-6.5V |
| Number of Channels | 1 |
| Operating Supply Current | 32mA |
| Nominal Supply Current | 70mA |
| Slew Rate | 2550V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 68 dB |
| Current - Input Bias | 10pA |
| Voltage - Supply, Single/Dual (±) | ±3.5V~6.5V |
| Output Current per Channel | 70mA |
| Input Offset Voltage (Vos) | 5mV |
| Bandwidth | 350MHz |
| Neg Supply Voltage-Nom (Vsup) | -6V |
| Unity Gain BW-Nom | 650000 kHz |
| Voltage Gain | 58dB |
| Average Bias Current-Max (IIB) | 0.0032μA |
| Power Supply Rejection Ratio (PSRR) | 58dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6.5V |
| Settling Time | 8 ns |
| Low-Bias | YES |
| Micropower | NO |
| -3db Bandwidth | 650MHz |
| Bias Current-Max (IIB) @25C | 0.00005μA |
| Programmable Power | NO |
| Dual Supply Voltage | 6V |
| Neg Supply Voltage-Max (Vsup) | -6.5V |
| Max I/O Voltage | 1mV |
| Input Offset Current-Max (IIO) | 0.0000025μA |
| Height | 1mm |
| Length | 3mm |
| Width | 3mm |
| Thickness | 880μm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA659IDRBT Overview
Op amp is packaged in 8-VDFN Exposed Pad case. The instrumentation amplifier in this picture is of the J-FET-type. A Tape & Reel (TR) case is used to deliver the buffer op amp. During the past two weeks, there have been close to 8 terminations. In this case, there are 8 pins on the board. This linear amplifier should be powered by an 6V battery. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. There are 8 pins on this chip. In terms of the input offset voltage, instrumentation amplifier rates at 5mV. The mounting type that is recommended for this electrical part is Surface Mount. With regard to operating temperature, this op amp functions well at -40°C~85°C. In order for this instrumentation amplifier to operate, the supply current needs to be between 32mA and 10 . Keeping the voltage gain at 58dB is the best course of action. As far as the device is concerned, buffer amplifier has 1 channels. The instrumentation amplifier is packed in the form of TR.
OPA659IDRBT Features
8 Pins
supply voltage of 6V
58dB voltage gain
OPA659IDRBT Applications
There are a lot of Texas Instruments OPA659IDRBT Instrumentational OP Amps applications.
- Wireless base stations
- Displayers for aircraft and air transportation control systems
- earphone
- Signal operation
- ECG equipment
- Power control
- Radiation thermometry transducers
- Large motor controllers
- Band-stop filter
- Instrumentation
