OPA725AIDBVT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Surface Mount | YES |
| Number of Pins | 5 |
| Operating Temperature | -40°C~125°C |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 6V |
| Base Part Number | OPA725 |
| Pin Count | 5 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 6V |
| Number of Channels | 1 |
| Operating Supply Current | 4.3mA |
| Nominal Supply Current | 5.5mA |
| Output Current | 40mA |
| Slew Rate | 30V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 94 dB |
| Current - Input Bias | 30pA |
| Voltage - Supply, Single/Dual (±) | 4V~12V ±2V~6V |
| Output Current per Channel | 40mA |
| Input Offset Voltage (Vos) | 3mV |
| Bandwidth | 20MHz |
| Neg Supply Voltage-Nom (Vsup) | -6V |
| Unity Gain BW-Nom | 20000 kHz |
| Voltage Gain | 120dB |
| Average Bias Current-Max (IIB) | 0.0002μA |
| Power Supply Rejection Ratio (PSRR) | 90.46dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 1.2mV |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.0002μA |
| Programmable Power | NO |
| Dual Supply Voltage | 5V |
| Max I/O Voltage | 3mV |
| Height | 1.45mm |
| Length | 2.9mm |
| Width | 1.6mm |
| Thickness | 1.2mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA725AIDBVT Overview
Packaging for the buffer amplifier is in the form of a SC-74A, SOT-753 case. General Purpose-type instrumentation amplifiers are used in this application. As far as the packaging is concerned, buffer op amp is delivered in a Cut Tape (CT) case. It is estimated that there will be 5 terminations in the next few months. The pins on this board total to 5 in total. I would like to remind you that this buffer op amp should be powered by an 6V battery. In more specific terms, this linear amplifier can be categoriOperational Amplifiered as a Operational Amplifier-type device. A total of 5 pins are present on the instrumentation amplifier. The input offset voltage is 3mV. This electrical part should be mounted using type Surface Mount. In relation to the operating temperature of this buffer op amp, it works well at an average of -40°C~125°C . Using an 4.3mA supply current, this operational amplifier ics can be operated. Maintain 120dB as the voltage gain. Buffer op amp is equipped with 1 channels on the device. This op amp ic outputs Rail-to-Rail signals, which is one of the many benefits it has. The operating supply voltage of instrumentation amplifier is rated 6V voltage. To pack the operational amplifier ics, TR is adopted as the packing method.
OPA725AIDBVT Features
5 Pins
supply voltage of 6V
120dB voltage gain
Output Type: Rail-to-Rail
OPA725AIDBVT Applications
There are a lot of Texas Instruments OPA725AIDBVT Instrumentational OP Amps applications.
- Medical imaging
- Weak signal detection
- Band-pass filter
- Strain gauges
- Micro signal measurement
- Video amplifiers
- Semiconductor detectors
- Test equipment
- Wireless base stations
- Switching amplifier
