OPA735AID
| Parameters | |
|---|---|
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.0002μA |
| Programmable Power | NO |
| Dual Supply Voltage | 5V |
| Nominal Gain Bandwidth Product | 1.6MHz |
| Max I/O Voltage | 5μV |
| Input Offset Current-Max (IIO) | 0.0003μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | OPA735 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 6V |
| Number of Channels | 1 |
| Operating Supply Current | 600μA |
| Nominal Supply Current | 750μA |
| Slew Rate | 1.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | Zero-Drift |
| Common Mode Rejection Ratio | 115 dB |
| Current - Input Bias | 100pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~12V ±1.35V~6V |
| Output Current per Channel | 20mA |
| Input Offset Voltage (Vos) | 5μV |
| Bandwidth | 1.6MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 1600 kHz |
| Voltage Gain | 130dB |
| Average Bias Current-Max (IIB) | 0.0002μA |
| Power Supply Rejection Ratio (PSRR) | 133.98dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Voltage - Input Offset | 1μV |
| Low-Bias | YES |
OPA735AID Overview
It is packaged in an 8-SOIC (0.154, 3.90mm Width)-case that protects the operational amplifiers from damage. An op amp ic of the Zero-Drift type. In the case of Tube cases, linear amplifier will be delivered. The number of terminations approaches 8. There are a total of 8 pins on this op amp. It would be helpful if you could remember that this op amp ic should be powered by an 5V battery. It should be noted that this type of buffer amplifier is exactly what is known as a Operational Amplifier device. 8 pins are included on the operational amplifiers. As far as the input offset voltage is concerned, linear amplifier rates at 5μV. Surface Mount is the recommended mounting type of operational amplifiers. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~85°C for optimal performance. You can run this op amp ic on 600μA . It is recommended to keep the voltage gain at 130dB at all times. The op amp ic has 1 channels on it. There are more than a few advantages to using this instrumentation amplifier, one of which is that it outputs Rail-to-Rail signals. The operating supply voltage of instrumentation amplifier is rated 6V voltage.
OPA735AID Features
8 Pins
supply voltage of 5V
130dB voltage gain
Output Type: Rail-to-Rail
OPA735AID Applications
There are a lot of Texas Instruments OPA735AID Instrumentational OP Amps applications.
- Non-polarized electrodes
- Broadcasting
- Multimedia playback equipment
- Displayers for aircraft and air transportation control systems
- Band-stop filter
- Measurements of Wheatstone bridge
- Switching amplifier
- Car stereo
- Power transmission
- Radiation thermometry transducers
