OPA820IDBVT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 6 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Surface Mount | YES |
| Number of Pins | 5 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | OPA820 |
| Pin Count | 5 |
| Operating Supply Voltage | 5V |
| Number of Channels | 1 |
| Operating Supply Current | 5.6mA |
| Nominal Supply Current | 5.75mA |
| Output Current | 110mA |
| Slew Rate | 240V/μs |
| Amplifier Type | Voltage Feedback |
| Common Mode Rejection Ratio | 74 dB |
| Current - Input Bias | 9μA |
| Voltage - Supply, Single/Dual (±) | 5V~12V ±2.5V~6V |
| Output Current per Channel | 110mA |
| Input Offset Voltage (Vos) | 200μV |
| Bandwidth | 800MHz |
| Gain Bandwidth Product | 280MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 280000 kHz |
| Voltage Gain | 65dB |
| Average Bias Current-Max (IIB) | 23μA |
| Power Supply Rejection Ratio (PSRR) | 68dB |
| Settling Time | 26 ns |
| Dual Supply Voltage | 5V |
| Max I/O Voltage | 1mV |
| Height | 1.45mm |
| Length | 2.9mm |
| Width | 1.6mm |
| Thickness | 1.2mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA820IDBVT Overview
Op amp is packaged in SC-74A, SOT-753 case. Op amps are Voltage Feedback types of amplifier on the chip. A Tape & Reel (TR) case is used to deliver the buffer op amp. A total of 5 terminations have been reported in the past few weeks. A total of 5 pins are located on this board. It would be helpful if you could remember that this op amp ic should be powered by an 5V battery. This particular linear amplifier is a type of Operational Amplifier device, to be precise. There are 5 pins on this chip. Op amp rates 200μV as input offset voltage. For this electronic part, it is recommended that you mount it with type Surface Mount. The buffer amplifier functions well at -40°C~85°C as far as operating temperature is concerned. In order for this instrumentation amplifier to operate, the supply current needs to be between 5.6mA and 10 . Voltage gain should remain at 65dB. 1 channels are available on the instrumentation amplifier. The operating supply voltage of the buffer op amp is rated at 5V.
OPA820IDBVT Features
5 Pins
supply voltage of 5V
65dB voltage gain
OPA820IDBVT Applications
There are a lot of Texas Instruments OPA820IDBVT Instrumentational OP Amps applications.
- High-frequency data acquisition systems
- pH (acidity)
- Video data acquisition
- ECG equipment
- Communication
- Tablets
- Large motor controllers
- Signal operation
- E-book readers
- Laptop
