Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-WFQFN Exposed Pad |
Number of Pins |
16 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
JESD-609 Code |
e3 |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
750mOhm |
Terminal Finish |
MATTE TIN |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
500mW |
Technology |
CMOS |
Terminal Position |
QUAD |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
3.3V |
Terminal Pitch |
0.5mm |
Time@Peak Reflow Temperature-Max (s) |
40 |
Base Part Number |
PI3A412 |
Output |
SEPARATE OUTPUT |
Number of Channels |
1 |
Number of Circuits |
4 |
Max Supply Voltage |
4.2V |
Min Supply Voltage |
1.8V |
Operating Supply Current |
1μA |
Max Supply Current |
1.5μA |
Turn On Delay Time |
20 ns |
Supply Type |
Single |
Turn-Off Delay Time |
12 ns |
-3db Bandwidth |
78MHz |
On-State Resistance (Max) |
750mOhm |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
65 dB |
Channel Capacitance (CS(off), CD(off)) |
20pF 20pF |
On-state Resistance Match-Nom |
0.08Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
13ns, 38ns |
Charge Injection |
50pC |
Channel-to-Channel Matching (ΔRon) |
50m Ω |
Crosstalk |
-97dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
25ns |
Switch-off Time-Max |
15ns |
Voltage - Supply, Single (V+) |
1.8V~4.2V |
Height Seated (Max) |
0.8mm |
Length |
3mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
PI3A412ZHEX Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-WFQFN Exposed Pad. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). Surface Mount is where this multiplexer is located. 2:1 is the ratio between multiplexers and demultiplexers. Operation at a temperature around -40°C~85°C TA. There are 16 terminations totally. The electronic part provides high-quality output because it has 1 channels. It is safe to turn on and run the electronic component with a 3.3V voltage supply. A SPDT switching circuit is used for these analog switches. A total of 4 circuits make up this switch device. Using the PI3A412 search parameter, you can discover variants of the switch. Internally, this switch multiplexer has a resistance of 750mOhm. Please refer to the datasheets for 16 pins functions. In this analog multiplexer, the value is Multiplexer or Switches. normally, users should not supply switches with voltages higher than 4.2V. A analog switch ic that has a cost-effective Single supply type. 1.8V should be the lowest voltage fed to the electronic component. For this digital switch to work, 1μA current would suffice. This analog switch requires a voltage of 1.8V~4.2V to drain from a single voltage supply. If put voltage greater than 1.5μA on the device, damage may be caused to the analogue multiplexer. In this switch multiplexer, there are SEPARATE OUTPUT outputs available.
PI3A412ZHEX Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
-3db Bandwidth: 78MHz
PI3A412ZHEX Applications
There are a lot of Diodes Incorporated PI3A412ZHEX Analog Switches & Multiplexers ICs applications.
- Avionics
- Cell phones
- Cable PC
- Wireless Local Loop
- Isolation
- Frame Relay Equipment
- DVD-R
- Communications systems
- MP3 players
- 65 V DACs