PI5A124TEX
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-6 |
| Number of Pins | 6 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Resistance | 10Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 550mW |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.95mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | PI5A124 |
| Number of Outputs | 2 |
| Polarity | Non-Inverting |
| Power Supplies | 3.3/5V |
| Number of Channels | 1 |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1μA |
| Power Dissipation | 550mW |
| Max Supply Current | 1μA |
| Throw Configuration | SPDT, SPST |
| Turn On Delay Time | 25 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 12 ns |
| -3db Bandwidth | 326MHz |
| On-State Resistance (Max) | 10Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Current - Leakage (IS(off)) (Max) | 200pA Typ |
| Channel Capacitance (CS(off), CD(off)) | 5.5pF 5.5pF |
| On-state Resistance Match-Nom | 1Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 15ns, 7ns |
| Charge Injection | 1.6pC |
| Channel-to-Channel Matching (ΔRon) | 200m Ω |
| Crosstalk | -43dB @ 10MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 40ns |
| Voltage - Supply, Single (V+) | 2V~6V |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
PI5A124TEX Overview
The electronic component is convenient to ship overseas because it is packed in a SOT-23-6. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). Mounted in Surface Mount is this multiplexer. The ratio between the number of multiplexer and demultiplexer circuits is 2:1. Operating temperature around -40°C~85°C TA extended. In total, 6 terminations have occurred. The electronic part delivers high-quality output through its 1 channels. A 3.3V voltage supply should turn on and run the electronic component. Unlike digital switches, these are based on SPDT switching circuits. Try searching for PI5A124 variants of the analog switch ic. Analog switches have 10Ohm internal resistance. The functions of 6 pins can be found in the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. In a normalsituation, users should not supply the switches with voltage higher than 6V. Analog switch ics with Single supply type are cost-effective. There should be 2V voltage fed to the electrical part below 2V. It would be sufficient to run this analogue multiplexer with 1μA current. Using a single voltage supply, this switch device consumes 2V~6V volts. If you put voltage higher than 1μA on the digital multiplexer, damage may occur. A analog switch ics with 2 outputs is included.
PI5A124TEX Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
-3db Bandwidth: 326MHz
PI5A124TEX Applications
There are a lot of Diodes Incorporated PI5A124TEX Analog Switches & Multiplexers ICs applications.
- E1 Network Equipment
- DSLAMs
- Wireless Local Loop
- PBXs
- Private Branch Exchange (PBX)
- Imaging
- Cross Connects
- DVD-R
- Avionics
- Isolation
