PI5A3157CEX
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 6-TSSOP, SC-88, SOT-363 |
| Number of Pins | 6 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Resistance | 13Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 180mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 2.3V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | PI5A3157 |
| Number of Outputs | 2 |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.65V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1μA |
| Power Dissipation | 180mW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 23 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 12.5 ns |
| -3db Bandwidth | 250MHz |
| On-State Resistance (Max) | 13Ohm |
| High Level Output Current | 128mA |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 57 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 2.3pF |
| On-state Resistance Match-Nom | 0.3Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 5.2ns, 3.5ns |
| Charge Injection | 7pC |
| Channel-to-Channel Matching (ΔRon) | 150m Ω |
| Crosstalk | -54dB @ 10MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 7ns |
| Voltage - Supply, Single (V+) | 1.65V~5.5V |
| Normal Position | NC |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
PI5A3157CEX Overview
The electronic component is convenient to ship overseas because it is packed in a 6-TSSOP, SC-88, SOT-363. High reliability is achieved by using advanced packaging method Tape & Reel (TR). Mounted in Surface Mount is this multiplexer. 2:1 is the ratio between multiplexers and demultiplexers. Extended operating temperature around -40°C~85°C TA. There are 6 terminations totally. A high-quality output is provided by the electrical component's 1 channels. When the electronic component is given a voltage of 2.3V, it should be turned on and run. Based on SPDT switching circuits, these analog multiplexers work. Use PI5A3157 to search for variants of the digital switches. The internal resistance of this digital multiplexer is 13Ohm. To find out what the 6 pins do, please refer to the datasheets. This switch device is a typical Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 5.5V. Analogue multiplexers of the Single supply type that are cost-effective. There should be 1.65V voltage fed to the electrical part below 1.65V. This digital switch can be operated with a current of 1μA. This analog switch requires a voltage of 1.65V~5.5V to drain from a single voltage supply. It may damage the digital multiplexer if the voltage is higher than 1μA. This digital multiplexer has 2 outputs.
PI5A3157CEX Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
-3db Bandwidth: 250MHz
PI5A3157CEX Applications
There are a lot of Diodes Incorporated PI5A3157CEX Analog Switches & Multiplexers ICs applications.
- Battery Powered Systems
- Ultrasound
- ISDN NT1/TA
- Wireless Local Loop
- Private Branch Exchange (PBX)
- Low-Voltage
- SDH/SONET multiplexers
- Precision test equipment
- Battery Powered Instruments
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
