PI5A3158BZAEX
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 12-WFDFN |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 12 |
| ECCN Code | EAR99 |
| Terminal Finish | MATTE TIN |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 180mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 1.8V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Output | SEPARATE OUTPUT |
| Qualification Status | Not Qualified |
| Polarity | Non-Inverting |
| Power Supplies | 1.8/5V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.65V |
| -3db Bandwidth | 350MHz |
| On-State Resistance (Max) | 11Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 63 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 2.5pF |
| On-state Resistance Match-Nom | 0.5Ohm |
| Switch Circuit | SPDT |
| Charge Injection | 5pC |
| Channel-to-Channel Matching (ΔRon) | 150m Ω |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.65V~5.5V |
| Height Seated (Max) | 0.8mm |
| Length | 3mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
PI5A3158BZAEX Overview
As the electronic part is packed in 12-WFDFN, international shipping is convenient. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). Mounted in Surface Mount is this multiplexer. The ratio between the number of multiplexer and demultiplexer circuits is 2:1. Increasing operating temperature to around -40°C~85°C TA. In total, there have been 12 terminations. As a result of its 1 channels, this electronic component provides high-quality output. It is safe to turn on and run the electronic component with a 1.8V voltage supply. On the other hand, analog switches can be constructed using SPDT switching circuits. A total of 2 circuits make up this switch device. There is Multiplexer or Switches analog multiplexer like this in the world. normally, users should not supply switches with voltages higher than 5.5V. It is recommended to use 1.65V as the lowest voltage for the electrical part. An analogue multiplexer drains from a single voltage supply at 1.65V~5.5V. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer.
PI5A3158BZAEX Features
1 Channels
Switch Circuit: SPDT
-3db Bandwidth: 350MHz
PI5A3158BZAEX Applications
There are a lot of Diodes Incorporated PI5A3158BZAEX Analog Switches & Multiplexers ICs applications.
- FTTH
- 65 V DACs
- USB 1.1 signal switching circuits
- Battery-powered systems
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Precision instrumentation
- PBX interfaces
- Isolation
- Residential Gateways, Home Gateway/Router
- Precision test equipment
