PI5A392AQE
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SSOP (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 18Ohm |
| Additional Feature | IT CAN ALSO OPERATE WITH 5 10% SUPPLY |
| Max Power Dissipation | 500mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.635mm |
| Base Part Number | PI5A392 |
| Number of Channels | 4 |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 2V |
| Power Dissipation | 500mW |
| Max Supply Current | 100nA |
| Turn On Delay Time | 40 ns |
| Number of Inputs | 4 |
| Supply Type | Single |
| Turn-Off Delay Time | 20 ns |
| -3db Bandwidth | 200MHz |
| On-State Resistance (Max) | 18Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 55 dB |
| Current - Leakage (IS(off)) (Max) | 30nA |
| Channel Capacitance (CS(off), CD(off)) | 13pF |
| On-state Resistance Match-Nom | 0.4Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 20ns, 10ns |
| Charge Injection | 5pC |
| Channel-to-Channel Matching (ΔRon) | 400m Ω |
| Crosstalk | -72dB @ 30MHz |
| Voltage - Supply, Single (V+) | 2V~6V |
| Height Seated (Max) | 1.75mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
PI5A392AQE Overview
The electrical component comes in 16-SSOP (0.154, 3.90mm Width) packaging, which makes it convenient to ship overseas. The advanced packaging method Tube provides high reliability. Surface Mount is where this multiplexer is located. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. An extended operating temperature of -40°C~85°C TA degrees Celsius. In total, there have been 16 terminations. A electrical component with 4 channels is capable of high-quality output. In the case of a voltage supply of 3.3V volts, the electrical part can be powered up and run. Based on SPST - NO switching circuits, these analog multiplexers work. Search with PI5A392 if you are looking for analog multiplexer variants. The internal resistance of this digital multiplexer is 18Ohm. For details about the functions of 16 pins, please refer to the datasheets. It is normally recommended that users do not supply the multiplexer with voltages higher than 6V. Analogue multiplexers of the Single supply type that are cost-effective. 2V is the lowest voltage that should be fed to the electronic electronic part. A voltage of 2V~6V is required for this switch device, which drains from a single voltage source. Putting voltage greater than 100nA on the multiplexer may cause damage. The 4 inputs need to be operated in order to work. Don’t miss additional features of the electronic component such as: IT CAN ALSO OPERATE WITH 5 10% SUPPLY.
PI5A392AQE Features
4 Channels
Switch Circuit: SPST - NO
-3db Bandwidth: 200MHz
Additional Features: IT CAN ALSO OPERATE WITH 5 10% SUPPLY
PI5A392AQE Applications
There are a lot of Diodes Incorporated PI5A392AQE Analog Switches & Multiplexers ICs applications.
- Digital Cross-Connects
- Frame Relay Equipment
- Industrial control systems
- Precision instrumentation
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- ATM
- Modems
- Multi-Line E1 Interface Cards
- High-Voltage
- Cable PC
