RT9728AHGE
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-6 |
| Surface Mount | YES |
| Number of Pins | 6 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| Feature | Status Flag |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Resistance | 120mOhm |
| Subcategory | Peripheral Drivers |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 1 |
| Supply Voltage | 3.6V |
| Terminal Pitch | 0.94mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 6 |
| Number of Outputs | 1 |
| Qualification Status | Not Qualified |
| Output Type | P-Channel |
| Max Output Current | 1.3A |
| Supply Voltage-Min (Vsup) | 2.5V |
| Interface | On/Off |
| Output Configuration | High Side |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Input Type | Non-Inverting |
| Switch Type | USB Switch |
| Nominal Input Voltage | 5.5V |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 2.5V~5.5V |
| Driver Number of Bits | 1 |
| Fault Protection | Current Limiting (Adjustable), Over Temperature, UVLO |
| Output Peak Current Limit-Nom | 1.295A |
| Rds On (Typ) | 120m Ω |
| Built-in Protections | TRANSIENT; OVER CURRENT; THERMAL; UNDER VOLTAGE |
| Output Current Flow Direction | SINK |
| Length | 2.8955mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
RT9728AHGE Overview
It is packaged in the form of a Tape & Reel (TR).It is included with the SOT-23-6 package as well.It has been mounted as Surface Mount on the LED driver.It owns USB Switch switch type.To ensure reliable operation, set the temperature to -40°C~85°C TA.It is possible to use 1 outputs in the lighting driver.The LED driving board is powered by a voltage of Not Required.A maximum output voltage of P-Channel volts can be obtained with this LED driver.A lighting driver with Status Flag features is available.There are 6 terminations in it.The operation is carried out using the 6 pins.The LED driving board has a total of 1 functions.The maximum output current is reduced to 1.3A to meet the operation criteria.The supply voltage of 3.6V is conducive to high efficiency.The LED driving board is equipped with a total of 6 pins.120mOhm is the resistance of the lighting driver.Self-contained in an econtainer with a capacity of Peripheral Drivers, this LED driver is self-contained.A normal operation requires that the supply voltage (Vsup) remain above 2.5V.
RT9728AHGE Features
Supplied from 3.6V
Resistance of 120mOhm
RT9728AHGE Applications
There are a lot of Richtek USA Inc. RT9728AHGE Power Switches ICs applications.
- PC Card Hot Swap
- Wireless/Networking Cards
- Smartphone and PDA
- Hard Disk Drives
- Hot-Swap Systems
- Storage Drives
- Low Voltage I/O System Power
- Storage (HDDs, SSDs)
- HDD and SSD
- Wireless Headsets
