SA5532AD
| Parameters | |
|---|---|
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Base Part Number | SA5532 |
| Pin Count | 8 |
| Operating Supply Voltage | 15V |
| Number of Elements | 2 |
| Power Supplies | +-5/+-15/10/30V |
| Operating Supply Current | 8mA |
| Nominal Supply Current | 16mA |
| Output Current | 38mA |
| Slew Rate | 9V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 200nA |
| Voltage - Supply, Single/Dual (±) | ±5V~15V |
| Output Current per Channel | 38mA |
| Input Offset Voltage (Vos) | 4mV |
| Bandwidth | 10MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 10000 kHz |
| Voltage Gain | 100dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 500μV |
| Low-Bias | NO |
| Micropower | NO |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 10MHz |
| Max I/O Voltage | 4mV |
| Power | YES |
| Input Offset Current-Max (IIO) | 0.15μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
SA5532AD Overview
It is packaged in an 8-SOIC (0.154, 3.90mm Width)-case that protects the operational amplifiers from damage. The instrumentation amplifier in this picture is of the General Purpose-type. Upon delivery, op amp ic is packaged in a Tube case. It is estimated that there will be 8 terminations in the next few months. Buffer amplifier has a total of 8 pins on it. It would be helpful if you could remember that this op amp ic should be powered by an 15V battery. In more specific terms, this linear amplifier can be categoriOperational Amplifiered as a Operational Amplifier-type device. 8 pins are available on the instrumentation amplifier. The input offset voltage is 4mV. This electronic part is recommended for mounting type Surface Mount. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~85°C for optimal performance. An 8mA volt supply current is needed for this linear amplifier to operate. The voltage gain should stay at 100dB. There is an operating supply voltage rating of 2 for this operational amplifier, which is rated at the manufacturer. The operating supply voltage of the buffer op amp is rated at 15V.
SA5532AD Features
8 Pins
supply voltage of 15V
100dB voltage gain
SA5532AD Applications
There are a lot of Texas Instruments SA5532AD Instrumentational OP Amps applications.
- Active probe
- Weak signal detection
- Home audio systems
- Automatic control
- Addition operation circuits
- Television
- Industrial control system
- Automation control systems
- High gain DC amplifier
- Tablets
