SA5534ADR2G
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| Published | 2005 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin (Sn) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | SA5534 |
| Pin Count | 8 |
| Number of Elements | 1 |
| Operating Supply Current | 4mA |
| Nominal Supply Current | 8mA |
| Power Dissipation | 750mW |
| Output Current | 38mA |
| Slew Rate | 13V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 500nA |
| Voltage - Supply, Single/Dual (±) | ±3V~20V |
| Halogen Free | Halogen Free |
| Output Current per Channel | 38mA |
| Input Offset Voltage (Vos) | 4mV |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 10000 kHz |
| Voltage Gain | 100dB |
| Average Bias Current-Max (IIB) | 2μA |
| Power Supply Rejection Ratio (PSRR) | 100dB |
| Low-Offset | NO |
| Frequency Compensation | YES AVCL>=3 |
| Supply Voltage Limit-Max | 22V |
| Voltage - Input Offset | 500μV |
| Neg Supply Voltage-Max (Vsup) | -22V |
| Nominal Gain Bandwidth Product | 10MHz |
| Height | 1.5mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SA5534ADR2G Overview
In order to protect the op amps, a 8-SOIC (0.154, 3.90mm Width) case is used. General Purpose-type instrumentation amplifiers are used in this application. A Tape & Reel (TR) case is used to deliver the buffer op amp. A total of 8 terminations have been reported in the past few weeks. A total of 8 pins are attached to buffer op amp. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 15V. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. In total, the buffer amplifier consists of 8 pins. As far as the input offset voltage is concerned, linear amplifier rates at 4mV. This electronic component is recommended to be mounted using the mounting type Surface Mount. It is important to note that this linear amplifier works well at a temperature of -40°C~85°C when it comes to operating temperatureAs long as the supply current of the chip does not exceed 4mA, this op amp ic can operate. Keeping the voltage gain at 100dB is the best course of action. The buffer op amp is rated for an operating voltage of 1 when it comes to the power supply. The linear amplifier is packaged by using a TAPE AND REEL axis.
SA5534ADR2G Features
8 Pins
supply voltage of 15V
100dB voltage gain
SA5534ADR2G Applications
There are a lot of ON Semiconductor SA5534ADR2G Instrumentational OP Amps applications.
- Digital cameras
- Large motor controllers
- Car stereo
- Biopotential
- Inverse/same-phase proportional circuit
- ECG equipment
- single/dual op amp sum and difference circuits
- High/low-pass filter circuit
- Proportional counter tubes
- Addition operation circuits
