SC2450ISWTRT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 28-SOIC (0.295, 7.50mm Width) |
| Surface Mount | YES |
| Number of Pins | 28 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2014 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 28 |
| ECCN Code | EAR99 |
| Terminal Finish | MATTE TIN |
| Subcategory | Switching Regulator or Controllers |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Function | Step-Down |
| Number of Outputs | 2 |
| Output Type | Transistor Driver |
| Input Voltage-Nom | 24V |
| Analog IC - Other Type | DUAL SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Output Current | 2A |
| Voltage - Supply (Vcc/Vdd) | 8.5V~30V |
| Control Features | Enable, Phase Control |
| Topology | Buck |
| Control Mode | VOLTAGE-MODE |
| Frequency - Switching | 135kHz~1MHz |
| Control Technique | PULSE WIDTH MODULATION |
| Synchronous Rectifier | Yes |
| Nominal Input Voltage | 30V |
| Switcher Configuration | PUSH-PULL |
| Max Duty Cycle | 45 % |
| Clock Sync | No |
| Length | 17.9mm |
| Width | 7.5mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
SC2450ISWTRT Overview
The switching controller fits in the 28-SOIC (0.295, 7.50mm Width) package and is ideal for most applications. 2 outputs are supported by the dc motor controller. PMIC packaging is solid with a Tape & Reel (TR) enclosure. Transistor Driver dc switching's outputs (s) are supported. A 8.5V~30V voltage is supplied to the dc control and used for operating it. Suitable for a -40°C~85°C TA dc switcher. The switching controller can be switched at 135kHz~1MHz. The Surface Mount makes it ideal for general dc dc regulator. Featured in the dcdc regulator is Enable, Phase Control which allows efficient switching control. The switch converters are connected to an analog IC with a DUAL SWITCHING CONTROLLER output. Switching converters are designed with the terminal (s) at position DUAL . An array of 28 terminations of dc switching. A few of the control techniques these dc dc converter ics adapt include PULSE WIDTH MODULATION. DC switcher's input voltageis 24V volts. Pins number 28 of switching converter in total. Specially, switching converter corresponds to type Switching Regulator or Controllers. If you are starting a new project, you should note the dc dc regulator's typical output current is 2A. voltage regulator dc to dcs with a 45 % duty cycle are designed to be reliable when powered on and powered off. You can set the input voltage to 30V for nominal working status.
SC2450ISWTRT Features
Transistor Driver Outputs
Switching Frequency: 135kHz~1MHz
Enable, Phase Control
PULSE WIDTH MODULATION
Max Duty Cycle: 45 %
SC2450ISWTRT Applications
There are a lot of Semtech Corporation SC2450ISWTRT DC to DC converter applications.
- Shearing machines
- PSRR circuits
- Electrical power transmission
- Domestic water pumps
- Post equipment
- Motor controller circuits
- Balance equipment
- SMT equipment
- Hydro power
- ATMs
